View P89LPC915HDH_299604.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core 2 kB 3 V Flash with 8-bit A/D converter
Rev. 04 -- 17 December 2004 Product data
1. General description
The P89LPC915/916/917 are single-chip microcontrollers in low-cost 14-pin and 16-pin packages, based on a high performance processor architecture that executes instructions in two to four clocks, six times the rate of standard 80C51 devices. Many system level functions have been incorporated into the P89LPC915/916/917 in order to reduce component count, board space, and system cost.
2. Features
s 2 kB byte-erasable Flash code memory organized into 256-byte sectors and 16-byte pages. Single-byte erasing allows any byte(s) to be used as non-volatile data storage. s 256-byte RAM data memory. s Two 16-bit counter/timers. Timer 0 (and Timer 1 - P89LPC917) may be configured to toggle a port output upon timer overflow or to become a PWM output. s 23-bit system timer that can also be used as a Real-Time clock. s 4-input multiplexed 8-bit A/D converter/single DAC output. Two analog comparators with selectable reference. s Enhanced UART with fractional baud rate generator, break detect, framing error detection, automatic address detection and versatile interrupt capabilities. s SPI communication port (P89LPC916). s Internal RC oscillator option allows operation without external oscillator components. The RC oscillator (factory calibrated to 1 %) option is selectable and fine tunable. s 2.4 V to 3.6 V VDD operating range. I/O pins are 5 V tolerant (may be pulled up or driven to 5.5 V). s Up to 14 I/O pins when using internal oscillator and reset options (P89LPC916, P89LPC917).
3. Additional features
* 14-pin (P89LPC915) and 16-pin (P89LPC916, P89LPC917) TSSOP packages. * A high performance 80C51 CPU provides instruction cycle times of 111 ns to
222 ns for all instructions except multiply and divide when executing at 18 MHz. This is six times the performance of the standard 80C51 running at the same clock frequency. A lower clock frequency for the same performance results in power savings and reduced EMI.
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
* In-Application Programming (IAP-Lite) and byte erase allows code memory to be
used for non-volatile data storage.
* Serial Flash In-Circuit Programming (ICP) allows simple production coding with
commercial EPROM programmers. Flash security bits prevent reading of sensitive application programs.
* Watchdog timer with separate on-chip oscillator, requiring no external
components. The Watchdog prescaler is selectable from 8 values.
* Low-voltage reset (Brownout detect) allows a graceful system shutdown when
power fails. May optionally be configured as an interrupt.
* Idle and two different power-down reduced power modes. Improved wake-up from
Power-down mode (a low interrupt input starts execution). Typical power-down current is 1 A (total power-down with voltage comparators disabled).
* Active-LOW reset. On-chip power-on reset allows operation without external reset
components. A reset counter and reset glitch suppression circuitry prevent spurious and incomplete resets. A software reset function is also available.
* Programmable port output configuration options: quasi-bidirectional, open drain,
push-pull, input-only.
* Port `input pattern match' detect. Port 0 may generate an interrupt when the value
of the pins match or do not match a programmable pattern.
* LED drive capability (20 mA) on all port pins. A maximum limit is specified for the
entire chip.
* Controlled slew rate port outputs to reduce EMI. Outputs have approximately 10 ns
minimum ramp times.
* Only power and ground connections are required to operate the
P89LPC915/916/917 when internal reset option is selected.
* Four interrupt priority levels. * Five (P89LPC916), six (P89LPC915), or seven (P89LPC917) keypad interrupt
inputs.
* Second data pointer. * Schmitt trigger port inputs. * Emulation support.
9397 750 14397
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
2 of 72
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
4. Ordering information
Table 1: Ordering information Package Name P89LPC915FDH P89LPC915HDH P89LPC916FDH P89LPC917FDH TSSOP14 TSSOP14 TSSOP16 TSSOP16 Description plastic thin shrink small outline package; 14 leads; body width 4.4 mm plastic thin shrink small outline package; 14 leads; body width 4.4 mm plastic thin shrink small outline package; 16 leads; body width 4.4 mm plastic thin shrink small outline package; 16 leads; body width 4.4 mm Version SOT402-1 SOT402-1 SOT403-1 SOT403-1 Type number
4.1 Ordering options
Table 2: Ordering options[1] Temperature range -40 C to +125 C -40 C to +85 C Frequency 0 MHz to 18 MHz Type number P89LPC915HDH P89LPC915FDH P89LPC916FDH P89LPC917FDH
[1] Please contact your local Philips sales office for availability of extended temperature (-40 C to +125 C) versions of the P89LPC916 and P89LPC917 devices.
9397 750 14397
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
3 of 72
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
5. Block diagram
P89LPC915
HIGH PERFORMANCE ACCELERATED 2-CLOCK 80C51 CPU
2 kB CODE FLASH 256-BYTE DATA RAM PORT 1 CONFIGURABLE I/Os PORT 0 CONFIGURABLE I/Os INTERNAL BUS
UART
I2C
ADC1/DAC1
REAL-TIME CLOCK/ SYSTEM TIMER TIMER 0 TIMER 1
KEYPAD INTERRUPT WATCHDOG TIMER AND OSCILLATOR
ANALOG COMPARATORS
PROGRAMMABLE OSCILLATOR DIVIDER external clock input ON-CHIP RC OSCILLATOR
CPU CLOCK
POWER MONITOR (POWER-ON RESET, BROWNOUT RESET)
002aaa822
Fig 1. P89LPC915 block diagram.
9397 750 14397
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
4 of 72
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
P89LPC916
HIGH PERFORMANCE ACCELERATED 2-CLOCK 80C51 CPU
2 kB CODE FLASH 256-BYTE DATA RAM PORT 2 CONFIGURABLE I/Os PORT 1 CONFIGURABLE I/Os PORT 0 CONFIGURABLE I/Os INTERNAL BUS
UART
I2C
ADC1/DAC1
SPI REAL-TIME CLOCK/ SYSTEM TIMER TIMER 0 TIMER 1
KEYPAD INTERRUPT WATCHDOG TIMER AND OSCILLATOR
ANALOG COMPARATORS
PROGRAMMABLE OSCILLATOR DIVIDER external clock input ON-CHIP RC OSCILLATOR
CPU CLOCK POWER MONITOR (POWER-ON RESET, BROWNOUT RESET)
002aaa823
Fig 2. P89LPC916 block diagram.
9397 750 14397
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
5 of 72
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
P89LPC917
HIGH PERFORMANCE ACCELERATED 2-CLOCK 80C51 CPU
2 kB CODE FLASH 256-BYTE DATA RAM PORT 2 CONFIGURABLE I/Os PORT 1 CONFIGURABLE I/Os PORT 0 CONFIGURABLE I/Os INTERNAL BUS
UART
I2C
ADC1/DAC1
REAL-TIME CLOCK/ SYSTEM TIMER TIMER 0 TIMER 1
KEYPAD INTERRUPT WATCHDOG TIMER AND OSCILLATOR
ANALOG COMPARATORS
PROGRAMMABLE OSCILLATOR DIVIDER external clock input ON-CHIP RC OSCILLATOR CLKOUT
CPU CLOCK POWER MONITOR (POWER-ON RESET, BROWNOUT RESET)
002aaa824
Fig 3. P89LPC917 block diagram.
9397 750 14397
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
6 of 72
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
6. Pinning information
6.1 Pinning
CIN2B/KBI1/AD10/P0.1 KBI0/CMP2/P0.0 RST/P1.5 VSS INT1/P1.4 SDA/INT0/P1.3 SCL/T0/P1.2
1 2 3 4 5 6 7
002aaa825
14 P0.2/CIN2A/KBI2/AD11 13 P0.3/CIN1B/KBI3/AD12 12 P0.4/CIN1A/KBI4/AD13/DAC1
LPC915
11 P0.5/CMPREF/KBI5/CLKIN 10 VDD 9 8 P1.0/TXD P1.1/RXD
Fig 4. P89LPC915 TSSOP14 pin configuration.
CIN2B/KBI1/AD10/P0.1 SS/P2.4 RST/P1.5 VSS MISO/P2.3 MOSI/P2.2 SDA/INT0/P1.3 SCL/T0/P1.2
1 2 3 4 5 6 7 8
002aaa826
16 P0.2/CIN2A/KBI2/AD11 15 P0.3/CIN1B/KB13/AD12 14 P0.4/CIN1A/KBI4/AD13/DAC1
LPC916
13 P0.5/CMPREF/KBI5/CLKIN 12 VDD 11 P2.5/SPICLK 10 P1.0/TXD 9 P1.1/RXD
Fig 5. P89LPC916 TSSOP16 pin configuration.
CIN2B/KBI1/AD10/P0.1 KBI0/CMP2/P0.0 RST/P1.5 VSS MOSI/P2.2 INT1/P1.4 SDA/INT0/P1.3 SCL/T0/P1.2
1 2 3 4 5 6 7 8
002aaa827
16 P0.2/CIN2A/KBI2/AD11 15 P0.3/CIN1B/KB13/AD12 14 P0.4/CIN1A/KBI4/AD13/DAC1
LPC917
13 P0.5/CMPREF/KBI5/CLKIN 12 VDD 11 P0.7/T1/KBI7/CLKOUT 10 P1.0/TXD 9 P1.1/RXD
Fig 6. P89LPC917 TSSOP16 pin configuration.
9397 750 14397
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
7 of 72
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
6.2 Pin description
Table 3: Symbol P0.0 to P0.5 P89LPC915 pin description Pin Type I/O Description Port 0: Port 0 is a 6-bit I/O port with user-configurable outputs. During reset Port 0 latches are configured in the input only mode with the internal pull-up disabled. The operation of Port 0 pins as inputs and outputs depends upon the port configuration selected. Each port pin is configured independently. Refer to Section 9.12.1 "Port configurations" and Table 13 "DC electrical characteristics" for details. The Keypad Interrupt feature operates with Port 0 pins. All pins have Schmitt triggered inputs. Port 0 also provides various special functions as described below: 2 I/O I I 1 I/O I I I 14 I/O I I I 13 I/O I I I 12 I/O I I I O 11 I/O I I I P0.0 -- Port 0 bit 0. CMP2 -- Comparator 2 output. KBI0 -- Keyboard input 0. P0.1 -- Port 0 bit 1. CIN2B -- Comparator 2 positive input B. KBI1 -- Keyboard input 1. AD10 -- A/D channel 1, input 0 P0.2 -- Port 0 bit 2. CIN2A -- Comparator 2 positive input A. KBI2 -- Keyboard input 2. AD11 -- A/D channel 1, input 1 P0.3 -- Port 0 bit 3. CIN1B -- Comparator 1 positive input B. KBI3 -- Keyboard input 3. AD12 -- A/D channel 1, input 2. P0.4 -- Port 0 bit 4. CIN1A -- Comparator 1 positive input A. KBI4 -- Keyboard input 4. AD13 -- A/D channel 1, input 3. DAC1 -- Digital to analog converter 1 output. P0.5 -- Port 0 bit 5. CMPREF -- Comparator reference (negative) input. KBI5 -- Keyboard input 5. CLKIN -- External clock input.
9397 750 14397
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
8 of 72
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
Table 3: Symbol
P89LPC915 pin description...continued Pin Type Description I/O Port 1: Port 1 is a 6-bit I/O port with user-configurable outputs. During reset Port 1 (P1.2); latches are configured in the input only mode with the internal pull-up disabled. The I (P1.5) operation of the inputs and outputs depends upon the port configuration selected. Refer to Section 9.12.1 "Port configurations" and Table 13 "DC electrical characteristics" for details. P1.2 is an open drain when used as an output. P1.5 is input only. All pins have Schmitt triggered inputs. Port 1 also provides various special functions as described below: 9 8 7 I/O O I/O I I/O I/O I/O 6 I/O I/O I/O 5 3 I/O I/O I I P1.0 -- Port 1 bit 0 TxD -- Serial port transmitter data. P1.1 -- Port 1 bit 0 RxD -- Serial port receiver data. P1.2 -- Port 1 bit 2. (Open drain when used as an output.) T0 -- Timer/counter 0 external count input, overflow output, or PWM output. SCL -- I2C-bus serial clock input/output. P1.3 -- Port 1 bit 2. (Open drain when used as an output.) INT0 -- External interrupt 0 input. SDA -- I2C-bus serial data input/output. P1.4 -- Port 1 bit 2. INT1 -- External interrupt 1input. P1.5 -- Port 1 bit 5. (Input only.) RST -- External Reset input during power-on or if selected via UCFG1. When functioning as a reset input a LOW on this pin resets the microcontroller, causing I/O ports and peripherals to take on their default states, and the processor begins execution at address 0. When using an oscillator frequency above 12 MHz, the reset input function of P1.5 must be enabled. An external circuit is required to hold the device in reset at power-up until VDD has reached its specified level. When system power is removed VDD will fall below the minimum specified operating voltage. When using an oscillator frequency above 12 MHz, in some applications, an external brownout detect circuit may be required to hold the device in reset when VDD falls below the minimum specified operating voltage. Also used during a power-on sequence to force In-System Programming mode. Ground: 0 V reference. Power Supply: This is the power supply voltage for normal operation as well as Idle and Power-down modes.
P1.0 to P1.5
VSS VDD
4 10
I I
9397 750 14397
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
9 of 72
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
Table 4: Symbol
P89LPC916 pin description Pin Type I/O Description Port 0: Port 0 is a 5-bit I/O port with user-configurable outputs. During reset Port 0 latches are configured in the input only mode with the internal pull-up disabled. The operation of Port 0 pins as inputs and outputs depends upon the port configuration selected. Each port pin is configured independently. Refer to Section 9.12.1 "Port configurations" and Table 13 "DC electrical characteristics" for details. The Keypad Interrupt feature operates with Port 0 pins. All pins have Schmitt triggered inputs. Port 0 also provides various special functions as described below: 1 I/O I I I 16 I/O I I I 15 I/O I I I 14 I/O I I I O 13 I/O I I I P0.1 -- Port 0 bit 1. CIN2B -- Comparator 2 positive input B. KBI1 -- Keyboard input 1. AD10 -- A/D channel 1, input 0 P0.2 -- Port 0 bit 2. CIN2A -- Comparator 2 positive input A. KBI2 -- Keyboard input 2. AD11 -- A/D channel 1, input 1 P0.3 -- Port 0 bit 3. CIN1B -- Comparator 1 positive input B. KBI3 -- Keyboard input 3. AD12 -- A/D channel 1, input 2. P0.4 -- Port 0 bit 4. CIN1A -- Comparator 1 positive input A. KBI4 -- Keyboard input 4. AD13 -- A/D channel 1, input 3. DAC1 -- Digital to analog converter 1 output. P0.5 -- Port 0 bit 5. CMPREF -- Comparator reference (negative) input. KBI5 -- Keyboard input 5. CLKIN -- External clock input.
P0.1 to P0.5
9397 750 14397
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
10 of 72
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
Table 4: Symbol
P89LPC916 pin description...continued Pin Type Description I/O Port 1: Port 1 is a 5-bit I/O port with user-configurable outputs. During reset Port 1 (P1.2); latches are configured in the input only mode with the internal pull-up disabled. The I (P1.5) operation of the P1.2 input and outputs depends upon the port configuration selected. Refer to Section 9.12.1 "Port configurations" and Table 13 "DC electrical characteristics" for details. P1.2 is an open drain when used as an output. P1.5 is input only. All pins have Schmitt triggered inputs. Port 1 also provides various special functions as described below: 10 9 8 I/O O I/O I I/O I/O I/O 7 I/O I/O I/O 3 I I P1.0 -- Port 1 bit 0 TxD -- Serial port transmitter data. P1.1 -- Port 1 bit 0 RxD -- Serial port receiver data. P1.2 -- Port 1 bit 2. (Open drain when used as an output.) T0 -- Timer/counter 0 external count input, overflow output, or PWM output. SCL -- I2C-bus serial clock input/output. P1.3 -- Port 1 bit 2. (Open drain when used as an output.) INT0 -- External interrupt 0 input. SDA -- I2C-bus serial data input/output. P1.5 -- Port 1 bit 5. (Input only.) RST -- External Reset input during power-on or if selected via UCFG1. When functioning as a reset input a LOW on this pin resets the microcontroller, causing I/O ports and peripherals to take on their default states, and the processor begins execution at address 0. When using an oscillator frequency above 12 MHz, the reset input function of P1.5 must be enabled. An external circuit is required to hold the device in reset at power-up until VDD has reached its specified level. When system power is removed VDD will fall below the minimum specified operating voltage. When using an oscillator frequency above 12 MHz, in some applications, an external brownout detect circuit may be required to hold the device in reset when VDD falls below the minimum specified operating voltage. Also used during a power-on sequence to force In-System Programming mode.
P1.0 to P1.5
9397 750 14397
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
11 of 72
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
Table 4: Symbol
P89LPC916 pin description...continued Pin Type I/O Description Port 2: Port 2 is a 4-bit I/O port having user-configurable output types. During reset Port 1 latches are configured in the input only mode with the internal pull-up disabled. The operation of the P2 input and outputs depends upon the port configuration selected. Refer to Section 9.12.1 "Port configurations" and Table 13 "DC electrical characteristics" for details. All pins have Schmitt triggered inputs. Port 2 also provides various special functions as described below: 6 I/O O 5 I/O I 2 11 I/O I/O I/O I/O P2.2 -- Port 2 bit 2. MOSI -- SPI master out slave in. When configured as a master this pin is an output. When configured as a slave, this pin is an input. P2.3 -- Port 2 bit 3. MISO -- SPI master in slave out. When configured as a master this pin is an input. When configured as a slave, this pin is an output. P2.4 -- Port 2 bit 4. SS -- SPI Slave select. P2.5 -- Port 2 bit 5. SPICLK -- When configured as a master this pin is an output. When configured as a slave, this pin is an input. Ground: 0 V reference. Power Supply: This is the power supply voltage for normal operation as well as Idle and Power-down modes.
P2.2 to P2.5
VSS VDD
4 12
I I
9397 750 14397
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
12 of 72
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
Table 5: Symbol
P89LPC917 pin description Pin Type I/O Description Port 0: Port 0 is a 7-bit I/O port with user-configurable outputs. During reset Port 0 latches are configured in the input only mode with the internal pull-up disabled. The operation of Port 0 pins as inputs and outputs depends upon the port configuration selected. Each port pin is configured independently. Refer to Section 9.12.1 "Port configurations" and Table 13 "DC electrical characteristics" for details. The Keypad Interrupt feature operates with Port 0 pins. All pins have Schmitt triggered inputs. Port 0 also provides various special functions as described below: 2 I/O I I 1 I/O I I I 16 I/O I I I 15 I/O I I I 14 I/O I I I O 13 I/O I I I 11 I/O I I I P0.0 -- Port 0 bit 0. CMP2 -- Comparator 2 output. KBI0 -- Keyboard input 0. P0.1 -- Port 0 bit 1. CIN2B -- Comparator 2 positive input B. KBI1 -- Keyboard input 1. AD10 -- A/D channel 1, input 0 P0.2 -- Port 0 bit 2. CIN2A -- Comparator 2 positive input A. KBI2 -- Keyboard input 2. AD11 -- A/D channel 1, input 1 P0.3 -- Port 0 bit 3. CIN1B -- Comparator 1 positive input B. KBI3 -- Keyboard input 3. AD12 -- A/D channel 1, input 2. P0.4 -- Port 0 bit 4. CIN1A -- Comparator 1 positive input A. KBI4 -- Keyboard input 4. AD13 -- A/D channel 1, input 3. DAC1 -- Digital to analog converter 1 output. P0.5 -- Port 0 bit 5. CMPREF -- Comparator reference (negative) input. KBI5 -- Keyboard input 5. CLKIN -- External clock input. P0.7 -- Port 0 bit 7. T1 -- Timer/counter 1 external count input, overflow output, or PWM output. KBI7 -- Keyboard input 7. CLKOUT -- Clock output.
P0.0 to P0.5
9397 750 14397
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
13 of 72
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
Table 5: Symbol
P89LPC917 pin description...continued Pin Type Description I/O Port 1: Port 1 is a 6-bit I/O port with user-configurable outputs. During reset Port 1 (P1.2); latches are configured in the input only mode with the internal pull-up disabled. The I (P1.5) operation of the outputs depends upon the port configuration selected. Refer to Section 9.12.1 "Port configurations" and Table 13 "DC electrical characteristics" for details. P1.2 and P1.3 are open drain when used as outputs. P1.5 is input only. All pins have Schmitt triggered inputs. Port 1 also provides various special functions as described below: 10 9 8 I/O O I/O I I/O I/O I/O 7 I/O I/O I/O 6 3 I/O I/O I I P1.0 -- Port 1 bit 0. TxD -- Serial port transmitter data. P1.1 -- Port 1 bit 1. RxD -- Serial port receiver data. P1.2 -- Port 1 bit 2. (Open drain when used as an output.) T0 -- Timer/counter 0 external count input, overflow, or PWM output. SCL -- I2C-bus serial clock input/output. P1.3 -- Port 1 bit 3. (Open drain when used as an output.) INT0 -- External interrupt 0 input. SDA -- I2C-bus serial data input/output. P1.4 -- Port 1 bit 4. INT1 -- External interrupt 1input. P1.5 -- Port 1 bit 5. (Input only.) RST -- External Reset input during power-on or if selected via UCFG1. When functioning as a reset input a LOW on this pin resets the microcontroller, causing I/O ports and peripherals to take on their default states, and the processor begins execution at address 0. When using an oscillator frequency above 12 MHz, the reset input function of P1.5 must be enabled. An external circuit is required to hold the device in reset at power-up until VDD has reached its specified level. When system power is removed VDD will fall below the minimum specified operating voltage. When using an oscillator frequency above 12 MHz, in some applications, an external brownout detect circuit may be required to hold the device in reset when VDD falls below the minimum specified operating voltage. Also used during a power-on sequence to force In-System Programming mode. Port 2: Port 2.2 is a single-bit I/O port with a user-configurable output. During reset the Port 2.2 latch is configured in the input only mode with the internal pull-up disabled. The operation of the output depends upon the port configuration selected. Refer to Section 9.12.1 "Port configurations" and Table 13 "DC electrical characteristics" for details. This pin has a Schmitt triggered input. Ground: 0 V reference. Power Supply: This is the power supply voltage for normal operation as well as Idle and Power-down modes.
P1.0 to P1.5
P2.2
5
I/O
VSS VDD
4 12
I I
9397 750 14397
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
14 of 72
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
7. Logic symbols
VDD VSS
DAC1
AD10 AD11 AD12 AD13 CLKIN
KBI0 KBI1 KBI2 KBI3 KBI4 KBI5
CMP2 CIN2B CIN2A CIN1B CIN1A CMPREF
P89LPC915
TxD RxD T0 INT0 INT1 RST
PORT 0
002aaa828
Fig 7. P89LPC915 logic symbol.
VDD
VSS
PORT 1
SCL SDA
DAC1
AD10 AD11 AD12 AD13 CLKIN
KBI1 KBI2 KBI3 KBI4 KBI5
CIN2B CIN2A CIN1B CIN1A CMPREF
PORT 0
PORT 1
TxD RxD T0 INT0 RST MOSI MISO SS SPICLK
SCL SDA
P89LPC916
PORT 2
002aaa829
Fig 8. P89LPC916 logic symbol.
VDD
VSS
DAC1
AD10 AD11 AD12 AD13 CLKIN CLKOUT
KBI0 KBI1 KBI2 KBI3 KBI4 KBI5 KBI7
CMP2 CIN2B CIN2A CIN1B CIN1A CMPREF T1
P89LPC917
TxD RxD T0 INT0 INT1 RST
PORT 0
PORT 2
002aaa830
Fig 9. P89LPC917 logic symbol.
PORT 1
SCL SDA
9397 750 14397
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
15 of 72
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
7.1 Product comparison
Table 6 highlights the differences between these three devices. For a complete list of device features, please see Section 2 "Features" on page 1.
Table 6: Product comparison Comp 2 output X X SPI X T1 PWM output X CLKOUT X INT1 X X KBI 6 5 7
Type number P89LPC915 P89LPC916 P89LPC917
8. Special function registers
Remark: Special Function Registers (SFRs) accesses are restricted in the following ways:
* User must not attempt to access any SFR locations not defined. * Accesses to any defined SFR locations must be strictly for the functions for the
SFRs.
* SFR bits labeled `-', `0' or `1' can only be written and read as follows:
- `-' Unless otherwise specified, must be written with `0', but can return any value when read (even if it was written with `0'). It is a reserved bit and may be used in future derivatives. - `0' must be written with `0', and will return a `0' when read. - `1' must be written with `1', and will return a `1' when read.
9397 750 14397
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
16 of 72
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Product data Rev. 04 -- 17 December 2004
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. 9397 750 14397
Philips Semiconductors
Table 7: P89LPC915 Special function registers * indicates SFRs that are bit addressable. Name Description SFR Bit functions and addresses addr. MSB Bit address ACC* ADCON1 ADINS ADMODA ADMODB AD1BH AD1BL AD1DAT0 AD1DAT1 AD1DAT2 AD1DAT3 AUXR1 B* BRGR0[2] BRGR1[2] BRGCON CMP1 CMP2 DIVM DPTR DPH DPL FMADRH FMADRL Accumulator A/D control register 1 A/D input select A/D mode register A A/D mode register B A/D_1 boundary high register A/D_1 boundary low register A/D_1 data register 0 A/D_1 data register 1 A/D_1 data register 2 A/D_1 data register 3 Auxiliary function register B register Baud rate generator rate low Baud rate generator rate high Baud rate generator control Comparator 1 control register Comparator 2 control register CPU clock divide-by-M control Data pointer (2 bytes) Data pointer high Data pointer low Program Flash address high Program Flash address low 83H 82H E7H E6H 00 00 00 00 00000000 00000000 00000000 00000000 E0H 97H A3H C0H A1H C4H BCH D5H D6H D7H F5H A2H F0H BEH BFH BDH ACH ADH 95H CE1 CE2 CP1 CP2 CN1 CN2 OE2 SBRGS CO1 CO2 BRGEN CMF1 CMF2 CLKLP F7 EBRR F6 F5 ENT0 F4 SRST F3 0 F2 F1 DPS F0 00 00 00 00[2] 00[1] 00[1] 00 00000000 00000000 00000000 xxxxxx00 xx000000 xx000000 00000000 Bit address ENBI1 ADI13 BNDI1 CLK2 ENADCI 1 ADI12 BURST1 CLK1 TMM1 ADI11 SCC1 CLK0 EDGE1 ADI10 SCAN1 ADCI1 ENDAC1 ENADC1 ADCS11 BSA1 E7 E6 E5 E4 E3 E2 E1 Reset value LSB E0 00 ADCS10 00 00 00 00 FF 00 00 00 00 00 00 00000000 00000000 00000000 00000000 000x0000 11111111 00000000 00000000 00000000 00000000 00000000 000000x0 Hex Binary
8-bit microcontrollers with accelerated two-clock 80C51 core
P89LPC915/916/917
17 of 72
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Table 7: P89LPC915 Special function registers...continued * indicates SFRs that are bit addressable. Name FMCON Description Program Flash Control (Read) Program Flash Control (Write) FMDATA I2ADR Program Flash data I2C-bus register Bit address I2CON* I2DAT
Rev. 04 -- 17 December 2004
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data 18 of 72
9397 750 14397
Philips Semiconductors
SFR Bit functions and addresses addr. MSB E4H BUSY FMCMD. 7 E5H DBH I2ADR.6 DF I2ADR.5 DE I2EN I2ADR.4 DD STA I2ADR.3 DC STO I2ADR.2 DB SI I2ADR.1 DA AA I2ADR.0 D9 FMCMD. 6 FMCMD. 5 FMCMD. 4 HVA FMCMD. 3 HVE FMCMD. 2 SV FMCMD. 1
Reset value LSB OI FMCMD. 0 00 GC D8 CRSEL 00 00 00 x00000x0 00000000 00 00000000 00000000 Hex 70 Binary 01110000
slave address
I2C-bus I2C-bus
control register data register
D8H DAH DDH DCH D9H Bit address A8H Bit address E8H Bit address B8H B7H Bit address
I2SCLH I2SCLL I2STAT IEN0* IEN1* IP0* IP0H
Serial clock generator/SCL duty cycle register high Serial clock generator/SCL duty cycle register low I2C-bus status register Interrupt enable 0 Interrupt enable 1 Interrupt priority 0 Interrupt priority 0 high
8-bit microcontrollers with accelerated two-clock 80C51 core
00000000 11111000 00000000 00x00000 x0000000 x0000000
STA.4 AF EA EF EAD BF FF PAD PADH -
STA.3 AE EWDRT EE EST BE PWDRT PWDRT H FE PST PSTH -
STA.2 AD EBO ED BD PBO PBOH FD -
STA.1 AC ES/ESR EC BC PS/PSR PSH/ PSRH FC -
STA.0 AB ET1 EB BB PT1 PT1H FB -
0 AA EX1 EA EC BA PX1 PX1H FA PC PCH -
0 A9 ET0 E9 EKBI B9 PT0 PT0H F9 PKBI PKBIH PATN _SEL
0 A8 EX0 E8 EI2C B8 PX0 PX0H F8 PI2C PI2CH KBIF
F8 00 00[1] 00[1] 00[1]
P89LPC915/916/917
IP1* IP1H KBCON KBMASK KBPATN
Interrupt priority 1 Interrupt priority 1 high Keypad control register Keypad interrupt mask register Keypad pattern register
F8H F7H 94H 86H 93H
00[1] 00[1] 00[1] 00 FF
00x00000 00x00000 xxxxxx00 00000000 11111111
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Table 7: P89LPC915 Special function registers...continued * indicates SFRs that are bit addressable. Name Description SFR Bit functions and addresses addr. MSB Bit address P0* Port 0 80H Bit address P1* P0M1 P0M2 P1M1 P1M2
Rev. 04 -- 17 December 2004
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data 19 of 72
9397 750 14397
Philips Semiconductors
Reset value LSB 84 CIN1A /KBI4 94 INT1 83 CIN1B /KBI3 93 INT0/ SDA 82 CIN2A /KBI2 92 T0/SCL 81 CIN2B /KBI1 91 RXD 80 CMP2 /KBI0 90 TXD
[1] [1]
Hex
Binary
87 97 SMOD1 RTCPD D7 CY RTCF
86 96 SMOD0 D6 AC RTCS1
85 CMPREF /KBI5 95 RST
Port 1 Port 0 output mode 1 Port 0 output mode 2 Port 1 output mode 1 Port 1 output mode 2 Power control register Power control register A Program status word Port 0 digital input disable Reset source register Real-time clock control Real-time clock register high Real-time clock register low Serial port address register Serial port address enable Serial Port data buffer register Serial port control Serial port extended status register Stack pointer Timer 0 and 1 auxiliary mode Timer 0 and 1 control
90H 84H 85H 91H 92H 87H B5H Bit address D0H F6H DFH D1H D2H D3H A9H B9H 99H
(P0M1.5) (P0M1.4) (P0M1.3) (P0M1.2) (P0M1.1) (P0M1.0) FF[1] (P0M2.5) (P0M2.4) (P0M2.3) (P0M2.2) (P0M2.1) (P0M2.0) BOPD VCPD D5 F0 BOF RTCS0 (P1M1.4) (P1M1.3) (P1M1.2) (P1M1.1) (P1M1.0) (P1M2.4) (P1M2.3) (P1M2.2) (P1M2.1) (P1M2.0) BOI ADPD D4 RS1 POF GF1 I2PD D3 RS0 R_BK GF0 D2 OV R_WD PMOD1 SPD D1 F1 R_SF ERTC PMOD0 D0 P R_EX RTCEN 60[1][6] 00[6] 00[6] 00 00 xx 00 00 00[1] D3[1] 00[1] 00 00[1]
11111111 00000000 11x1xx11 00x0xx00 00000000
PCON PCONA PSW* PT0AD RSTSRC RTCCON RTCH RTCL SADDR SADEN SBUF SCON* SSTAT SP TAMOD TCON*
8-bit microcontrollers with accelerated two-clock 80C51 core
00000000 00000000 xx00000x
[3]
PT0AD.5 PT0AD.4 PT0AD.3 PT0AD.2 PT0AD.1
011xxx00 00000000 00000000 00000000 00000000 xxxxxxxx 00000000 00000000 00000111 xxx0xxx0 00000000
P89LPC915/916/917
Bit address 98H BAH 81H 8FH 88H
9F SM0/FE DBMOD
9E SM1 INTLO
9D SM2 CIDIS
9C REN DBISEL
9B TB8 FE
9A RB8 BR
99 TI OE
98 RI STINT 00 00 07
8F TF1
8E TR1
8D TF0
8C TR0
8B IE1
8A IT1
89 IE0
T0M2 88 IT0
00 00
Bit address
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Table 7: P89LPC915 Special function registers...continued * indicates SFRs that are bit addressable. Name TH0 TH1 TL0 TL1 TMOD TRIM WDCON WDL WFEED1 WFEED2
[1] [2] [3] [4] [5] [6] Rev. 04 -- 17 December 2004
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data 20 of 72
9397 750 14397
Philips Semiconductors
Description Timer 0 high Timer 1 high Timer 0 low Timer 1 low Timer 0 and 1 mode Internal oscillator trim register Watchdog control register Watchdog load Watchdog feed 1 Watchdog feed 2
SFR Bit functions and addresses addr. MSB 8CH 8DH 8AH 8BH 89H 96H A7H C1H C2H C3H T1GATE RCCLK PRE2 T1C/T PRE1 T1M1 TRIM.5 PRE0 T1M0 TRIM.4 T0GATE TRIM.3 T0C/T TRIM.2 WDRUN T0M1 TRIM.1 WDTOF
Reset value LSB Hex 00 00 00 00 T0M0 TRIM.0 WDCLK FF 00 Binary 00000000 00000000 00000000 00000000 00000000
[5] [6] [4] [6]
11111111
8-bit microcontrollers with accelerated two-clock 80C51 core
All ports are in input only (high impedance) state after power-up. BRGR1 and BRGR0 must only be written if BRGEN in BRGCON SFR is logic 0. If any are written while BRGEN = 1, the result is unpredictable. The RSTSRC register reflects the cause of the P89LPC915/916/917 reset. Upon a power-up reset, all reset source flags are cleared except POF and BOF; the power-on reset value is xx110000. After reset, the value is 111001x1, i.e., PRE[2:0] are all logic 1, WDRUN = 1 and WDCLK = 1. WDTOF bit is logic 1 after Watchdog reset and is logic 0 after power-on reset. Other resets will not affect WDTOF. On power-on reset, the TRIM SFR is initialized with a factory preprogrammed value. Other resets will not cause initialization of the TRIM register. The only reset source that affects these SFRs is power-on reset
P89LPC915/916/917
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Product data Rev. 04 -- 17 December 2004
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. 9397 750 14397
Philips Semiconductors
Table 8: P89LPC916 Special function registers * indicates SFRs that are bit addressable. Name Description SFR Bit functions and addresses addr. MSB Bit address ACC* ADCON1 ADINS ADMODA ADMODB AD1BH AD1BL AD1DAT0 AD1DAT1 AD1DAT2 AD1DAT3 AUXR1 B* BRGR0[2] BRGR1[2] BRGCON CMP1 CMP2 DIVM DPTR DPH DPL FMADRH FMADRL Accumulator A/D control register 1 A/D input select A/D mode register A A/D mode register B A/D_1 boundary high register A/D_1 boundary low register A/D_1 data register 0 A/D_1 data register 1 A/D_1 data register 2 A/D_1 data register 3 Auxiliary function register B register Baud rate generator rate low Baud rate generator rate high Baud rate generator control Comparator 1 control register Comparator 2 control register CPU clock divide-by-M control Data pointer (2 bytes) Data pointer high Data pointer low Program Flash address high Program Flash address low 83H 82H E7H E6H 00 00 00 00 00000000 00000000 00000000 00000000 E0H 97H A3H C0H A1H C4H BCH D5H D6H D7H F5H A2H F0H BEH BFH BDH ACH ADH 95H CE1 CE2 CP1 CP2 CN1 CN2 OE2 SBRGS CO1 CO2 BRGEN CMF1 CMF2 CLKLP F7 EBRR F6 F5 ENT0 F4 SRST F3 0 F2 F1 DPS F0 00 00 00 00[2] 00[1] 00 00 00000000 00000000 00000000 xxxxxx00 xx000000 xx000000 00000000 Bit address ENBI1 ADI13 BNDI1 CLK2 ENADCI 1 ADI12 BURST1 CLK1 TMM1 ADI11 SCC1 CLK0 EDGE1 ADI10 SCAN1 ADCI1 ENDAC1 ENADC1 ADCS11 BSA1 E7 E6 E5 E4 E3 E2 E1 Reset value LSB E0 00 ADCS10 00 00 00 00 FF 00 00 00 00 00 00 00000000 00000000 00000000 00000000 000x0000 11111111 00000000 00000000 00000000 00000000 00000000 000000x0 Hex Binary
8-bit microcontrollers with accelerated two-clock 80C51 core
P89LPC915/916/917
21 of 72
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Table 8: P89LPC916 Special function registers...continued * indicates SFRs that are bit addressable. Name FMCON Description Program Flash Control (Read) Program Flash Control (Write) FMDATA I2ADR Program Flash data I2C-bus register Bit address I2CON* I2DAT
Rev. 04 -- 17 December 2004
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data 22 of 72
9397 750 14397
Philips Semiconductors
SFR Bit functions and addresses addr. MSB E4H BUSY FMCMD. 7 E5H DBH I2ADR.6 DF I2ADR.5 DE I2EN I2ADR.4 DD STA I2ADR.3 DC STO I2ADR.2 DB SI I2ADR.1 DA AA I2ADR.0 D9 FMCMD. 6 FMCMD. 5 FMCMD. 4 HVA FMCMD. 3 HVE FMCMD. 2 SV FMCMD. 1
Reset value LSB OI FMCMD. 0 00 GC D8 CRSEL 00 00 00 x00000x0 00000000 00 00000000 00000000 Hex 70 Binary 01110000
slave address
I2C-bus I2C-bus
control register data register
D8H DAH DDH DCH D9H Bit address A8H Bit address E8H Bit address B8H B7H Bit address
I2SCLH I2SCLL I2STAT IEN0* IEN1* IP0* IP0H
Serial clock generator/SCL duty cycle register high Serial clock generator/SCL duty cycle register low I2C-bus status register Interrupt enable 0 Interrupt enable 1 Interrupt priority 0 Interrupt priority 0 high
8-bit microcontrollers with accelerated two-clock 80C51 core
00000000 11111000 00000000 00x00000 x0000000 x0000000
STA.4 AF EA EF EAD BF FF PAD PADH -
STA.3 AE EWDRT EE EST BE PWDRT PWDRT H FE PST PSTH -
STA.2 AD EBO ED BD PBO PBOH FD -
STA.1 AC ES/ESR EC BC PS/PSR PSH/ PSRH FC -
STA.0 AB ET1 EB ESPI BB PT1 PT1H FB PSPI PSPIH -
0 AA EA EC BA FA PC PCH -
0 A9 ET0 E9 EKBI B9 PT0 PT0H F9 PKBI PKBIH PATN _SEL
0 A8 EX0 E8 EI2C B8 PX0 PX0H F8 PI2C PI2CH KBIF
F8 00 00[1] 00[1] 00[1]
P89LPC915/916/917
IP1* IP1H KBCON KBMASK KBPATN
Interrupt priority 1 Interrupt priority 1 high Keypad control register Keypad interrupt mask register Keypad pattern register
F8H F7H 94H 86H 93H
00[1] 00[1] 00[1] 00 FF
00x00000 00x00000 xxxxxx00 00000000 11111111
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Table 8: P89LPC916 Special function registers...continued * indicates SFRs that are bit addressable. Name Description SFR Bit functions and addresses addr. MSB Bit address P0* Port 0 80H Bit address P1* Port 1 90H Bit address P2* P0M1 P0M2
Rev. 04 -- 17 December 2004
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data 23 of 72
9397 750 14397
Philips Semiconductors
Reset value LSB 84 CIN1A /KBI4 94 94 SS 83 CIN1B /KBI3 93 INT0/ SDA 93 MISO 82 CIN2A /KBI2 92 T0/SCL 92 MOSI 81 CIN2B /KBI1 91 RXD 91 80 90 TXD 90 FF[1] 00[1] 00[1] FF[1] 00[1] 00 00[1] 00 00 60[1][6] 00[6] 00[6] 00 00 xx
[1] [1] [1]
Hex
Binary
87 97 97 SMOD1 RTCPD D7 CY RTCF
86 96 96 SMOD0 D6 AC RTCS1
85 CMPREF /KBI5 95 RST 95 SPICLK
Port 2 Port 0 output mode 1 Port 0 output mode 2 Port 1 output mode 1 Port 1 output mode 2 Port 2 output mode 1 Port 2 output mode 2 Power control register Power control register A Program status word Port 0 digital input disable Reset source register Real-time clock control Real-time clock register high Real-time clock register low Serial port address register Serial port address enable Serial Port data buffer register Serial port control Serial port extended status register
A0H 84H 85H 91H 92H A4H A5H 87H B5H Bit address D0H F6H DFH D1H D2H D3H A9H B9H 99H
(P0M1.5) (P0M1.4) (P0M1.3) (P0M1.2) (P0M1.1) (P0M2.5) (P0M2.4) (P0M2.3) (P0M2.2) (P0M2.1) -
11111111 00000000 11x1xx11
P1M1 P1M2 P2M1 P2M2 PCON PCONA PSW* PT0AD RSTSRC RTCCON RTCH RTCL SADDR SADEN SBUF SCON* SSTAT
(P1M1.3) (P1M1.2) (P1M1.1) (P1M1.0) D3[1] (P1M2.3) (P1M2.2) (P1M2.1) (P1M2.0) PMOD1 SPD D1 F1 R_SF ERTC PMOD0 D0 P R_EX RTCEN
8-bit microcontrollers with accelerated two-clock 80C51 core
00x0xx00 11111111 00000000 00000000 00000000 00000000 xx00000x
[3]
(P2M1.5) (P2M1.4) (P2M1.3) (P2M1.2) (P2M2.5) (P2M2.4) (P2M2.3) (P2M2.2) BOPD VCPD D5 F0 BOF RTCS0 BOI ADPD D4 RS1 POF GF1 I2PD D3 RS0 R_BK GF0 SPPD D2 OV R_WD -
P89LPC915/916/917
PT0AD.5 PT0AD.4 PT0AD.3 PT0AD.2 PT0AD.1
011xxx00 00000000 00000000 00000000 00000000 xxxxxxxx 00000000 00000000
Bit address 98H BAH
9F SM0/FE DBMOD
9E SM1 INTLO
9D SM2 CIDIS
9C REN DBISEL
9B TB8 FE
9A RB8 BR
99 TI OE
98 RI STINT 00 00
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Table 8: P89LPC916 Special function registers...continued * indicates SFRs that are bit addressable. Name SP SPCTL SPSTAT SPDAT TAMOD TCON* TH0 TH1 TL0 TL1 TMOD TRIM WDCON WDL WFEED1 WFEED2
[1] [2] [3]
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data Rev. 04 -- 17 December 2004 24 of 72
9397 750 14397
Philips Semiconductors
Description Stack pointer SPI control register SPI status register SPI data register Timer 0 and 1 auxiliary mode Timer 0 and 1 control Timer 0 high Timer 1 high Timer 0 low Timer 1 low Timer 0 and 1 mode Internal oscillator trim register Watchdog control register Watchdog load Watchdog feed 1 Watchdog feed 2
SFR Bit functions and addresses addr. MSB 81H E2H E1H E3H 8FH 88H 8CH 8DH 8AH 8BH 89H 96H A7H C1H C2H C3H T1GATE RCCLK PRE2 T1C/T PRE1 T1M1 TRIM.5 PRE0 T1M0 TRIM.4 T0GATE TRIM.3 T0C/T TRIM.2 WDRUN T0M1 TRIM.1 WDTOF 8F TF1 8E TR1 8D TF0 8C TR0 8B 8A 89 IE0 SSIG SPIF SPEN WCOL DORD MSTR CPOL CPHA SPR1 -
Reset value LSB SPR0 T0M2 88 IT0 00 00 00 00 00 T0M0 TRIM.0 WDCLK FF 00 00000000 00000000 00000000 00000000 00000000 00000000
[5] [6] [4] [6]
Hex 07 04 00 00 00
Binary 00000111 00000100 00xxxxxx 00000000 xxx0xxx0
Bit address
8-bit microcontrollers with accelerated two-clock 80C51 core
11111111
P89LPC915/916/917
[4] [5] [6]
All ports are in input only (high impedance) state after power-up. BRGR1 and BRGR0 must only be written if BRGEN in BRGCON SFR is logic 0. If any are written while BRGEN = 1, the result is unpredictable. The RSTSRC register reflects the cause of the P89LPC915/916/917 reset. Upon a power-up reset, all reset source flags are cleared except POF and BOF; the power-on reset value is xx110000. After reset, the value is 111001x1, i.e., PRE[2:0] are all logic 1, WDRUN = 1 and WDCLK = 1. WDTOF bit is logic 1 after Watchdog reset and is logic 0 after power-on reset. Other resets will not affect WDTOF. On power-on reset, the TRIM SFR is initialized with a factory preprogrammed value. Other resets will not cause initialization of the TRIM register. The only reset source that affects these SFRs is power-on reset.
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Product data Rev. 04 -- 17 December 2004
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. 9397 750 14397
Philips Semiconductors
Table 9: P89LPC917 Special function registers * indicates SFRs that are bit addressable. Name Description SFR Bit functions and addresses addr. MSB Bit address ACC* ADCON1 ADINS ADMODA ADMODB AD1BH AD1BL AD1DAT0 AD1DAT1 AD1DAT2 AD1DAT3 AUXR1 B* BRGR0[2] BRGR1[2] BRGCON CMP1 CMP2 DIVM DPTR DPH DPL FMADRH FMADRL Accumulator A/D control register 1 A/D input select A/D mode register A A/D mode register B A/D_1 boundary high register A/D_1 boundary low register A/D_1 data register 0 A/D_1 data register 1 A/D_1 data register 2 A/D_1 data register 3 Auxiliary function register B register Baud rate generator rate low Baud rate generator rate high Baud rate generator control Comparator 1 control register Comparator 2 control register CPU clock divide-by-M control Data pointer (2 bytes) Data pointer high Data pointer low Program Flash address high Program Flash address low 83H 82H E7H E6H 00 00 00 00 00000000 00000000 00000000 00000000 E0H 97H A3H C0H A1H C4H BCH D5H D6H D7H F5H A2H F0H BEH BFH BDH ACH ADH 95H CE1 CE2 CP1 CP2 CN1 CN2 OE2 SBRGS CO1 CO2 BRGEN CMF1 CMF2 CLKLP F7 EBRR F6 ENT1 F5 ENT0 F4 SRST F3 0 F2 F1 DPS F0 00 00 00 00[2] 00[1] 00[1] 00 00000000 00000000 00000000 xxxxxx00 xx000000 xx000000 00000000 Bit address ENBI1 ADI13 BNDI1 CLK2 ENADCI 1 ADI12 BURST1 CLK1 TMM1 ADI11 SCC1 CLK0 EDGE1 ADI10 SCAN1 ADCI1 ENDAC1 ENADC1 ADCS11 BSA1 E7 E6 E5 E4 E3 E2 E1 Reset value LSB E0 00 ADCS10 00 00 00 00 FF 00 00 00 00 00 00 00000000 00000000 00000000 00000000 000x0000 11111111 00000000 00000000 00000000 00000000 00000000 000000x0 Hex Binary
8-bit microcontrollers with accelerated two-clock 80C51 core
P89LPC915/916/917
25 of 72
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Table 9: P89LPC917 Special function registers...continued * indicates SFRs that are bit addressable. Name FMCON Description Program Flash Control (Read) Program Flash Control (Write) FMDATA I2ADR Program Flash data I2C-bus register Bit address I2CON* I2DAT
Rev. 04 -- 17 December 2004
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data 26 of 72
9397 750 14397
Philips Semiconductors
SFR Bit functions and addresses addr. MSB E4H BUSY FMCMD. 7 E5H DBH I2ADR.6 DF I2ADR.5 DE I2EN I2ADR.4 DD STA I2ADR.3 DC STO I2ADR.2 DB SI I2ADR.1 DA AA I2ADR.0 D9 FMCMD. 6 FMCMD. 5 FMCMD. 4 HVA FMCMD. 3 HVE FMCMD. 2 SV FMCMD. 1
Reset value LSB OI FMCMD. 0 00 GC D8 CRSEL 00 00 00 x00000x0 00000000 00 00000000 00000000 Hex 70 Binary 01110000
slave address
I2C-bus I2C-bus
control register data register
D8H DAH DDH DCH D9H Bit address A8H Bit address E8H Bit address B8H B7H Bit address
I2SCLH I2SCLL I2STAT IEN0* IEN1* IP0* IP0H
Serial clock generator/SCL duty cycle register high Serial clock generator/SCL duty cycle register low I2C-bus status register Interrupt enable 0 Interrupt enable 1 Interrupt priority 0 Interrupt priority 0 high
8-bit microcontrollers with accelerated two-clock 80C51 core
00000000 11111000 00000000 00x00000 x0000000 x0000000
STA.4 AF EA EF EAD BF FF PAD PADH -
STA.3 AE EWDRT EE EST BE PWDRT PWDRT H FE PST PSTH -
STA.2 AD EBO ED BD PBO PBOH FD -
STA.1 AC ES/ESR EC BC PS/PSR PSH/ PSRH FC -
STA.0 AB ET1 EB BB PT1 PT1H FB -
0 AA EX1 EA EC BA PX1 PX1H FA PC PCH -
0 A9 ET0 E9 EKBI B9 PT0 PT0H F9 PKBI PKBIH PATN _SEL
0 A8 EX0 E8 EI2C B8 PX0 PX0H F8 PI2C PI2CH KBIF
F8 00 00[1] 00[1] 00[1]
P89LPC915/916/917
IP1* IP1H KBCON KBMASK KBPATN
Interrupt priority 1 Interrupt priority 1 high Keypad control register Keypad interrupt mask register Keypad pattern register
F8H F7H 94H 86H 93H
00[1] 00[1] 00[1] 00 FF
00x00000 00x00000 xxxxxx00 00000000 11111111
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Table 9: P89LPC917 Special function registers...continued * indicates SFRs that are bit addressable. Name Description SFR Bit functions and addresses addr. MSB Bit address P0* Port 0 80H Bit address P1* P0M1 P0M2 P1M1 P1M2
Rev. 04 -- 17 December 2004
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data 27 of 72
9397 750 14397
Philips Semiconductors
Reset value LSB 84 CIN1A /KBI4 94 INT1 83 CIN1B /KBI3 93 INT0/ SDA 82 CIN2A /KBI2 92 T0/SCL 81 CIN2B /KBI1 91 RXD 80 CMP2 /KBI0 90 TXD
[1] [1]
Hex
Binary
87 T1/KBI7/ CLKOUT 97 (P0M1.7) (P0M2.7) SMOD1 RTCPD D7 CY RTCF
86 96 SMOD0 D6 AC RTCS1
85 CMPREF /KBI5 95 RST
Port 1 Port 0 output mode 1 Port 0 output mode 2 Port 1 output mode 1 Port 1 output mode 2 Power control register Power control register A Program status word Port 0 digital input disable Reset source register Real-time clock control Real-time clock register high Real-time clock register low Serial port address register Serial port address enable Serial Port data buffer register Serial port control Serial port extended status register Stack pointer Timer 0 and 1 auxiliary mode Timer 0 and 1 control
90H 84H 85H 91H 92H 87H B5H Bit address D0H F6H DFH D1H D2H D3H A9H B9H 99H
(P0M1.5) (P0M1.4) (P0M1.3) (P0M1.2) (P0M1.1) (P0M1.0) FF[1] (P0M2.5) (P0M2.4) (P0M2.3) (P0M2.2) (P0M2.1) (P0M2.0) BOPD VCPD D5 F0 BOF RTCS0 (P1M1.4) (P1M1.3) (P1M1.2) (P1M1.1) (P1M1.0) (P1M2.4) (P1M2.3) (P1M2.2) (P1M2.1) (P1M2.0) BOI ADPD D4 RS1 POF GF1 I2PD D3 RS0 R_BK GF0 D2 OV R_WD PMOD1 SPD D1 F1 R_SF ERTC PMOD0 D0 P R_EX RTCEN 60[1][6] 00[6] 00[6] 00 00 xx 00 00 00[1] D3[1] 00[1] 00 00[1]
11111111 00000000 11x1xx11 00x0xx00 00000000
PCON PCONA PSW* PT0AD RSTSRC RTCCON RTCH RTCL SADDR SADEN SBUF SCON* SSTAT SP TAMOD TCON*
8-bit microcontrollers with accelerated two-clock 80C51 core
00000000 00000000 xx00000x
[3]
PT0AD.5 PT0AD.4 PT0AD.3 PT0AD.2 PT0AD.1
011xxx00 00000000 00000000 00000000 00000000 xxxxxxxx 00000000 00000000 00000111 xxx0xxx0 00000000
P89LPC915/916/917
Bit address 98H BAH 81H 8FH 88H
9F SM0/FE DBMOD
9E SM1 INTLO
9D SM2 CIDIS
9C REN DBISEL
9B TB8 FE
9A RB8 BR
99 TI OE
98 RI STINT 00 00 07
8F TF1
8E TR1
8D TF0
T1M2 8C TR0
8B IE1
8A IT1
89 IE0
T0M2 88 IT0
00 00
Bit address
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Table 9: P89LPC917 Special function registers...continued * indicates SFRs that are bit addressable. Name TH0 TH1 TL0 TL1 TMOD TRIM WDCON WDL WFEED1 WFEED2
[1] [2] [3] [4] [5] [6] Rev. 04 -- 17 December 2004
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data 28 of 72
9397 750 14397
Philips Semiconductors
Description Timer 0 high Timer 1 high Timer 0 low Timer 1 low Timer 0 and 1 mode Internal oscillator trim register Watchdog control register Watchdog load Watchdog feed 1 Watchdog feed 2
SFR Bit functions and addresses addr. MSB 8CH 8DH 8AH 8BH 89H 96H A7H C1H C2H C3H T1GATE RCCLK PRE2 T1C/T ENCLK PRE1 T1M1 TRIM.5 PRE0 T1M0 TRIM.4 T0GATE TRIM.3 T0C/T TRIM.2 WDRUN T0M1 TRIM.1 WDTOF
Reset value LSB Hex 00 00 00 00 T0M0 TRIM.0 WDCLK FF 00 Binary 00000000 00000000 00000000 00000000 00000000
[5] [6] [4] [6]
11111111
8-bit microcontrollers with accelerated two-clock 80C51 core
All ports are in input only (high impedance) state after power-up. BRGR1 and BRGR0 must only be written if BRGEN in BRGCON SFR is logic 0. If any are written while BRGEN = 1, the result is unpredictable. The RSTSRC register reflects the cause of the P89LPC915/916/917 reset. Upon a power-up reset, all reset source flags are cleared except POF and BOF; the power-on reset value is xx110000. After reset, the value is 111001x1, i.e., PRE[2:0] are all logic 1, WDRUN = 1 and WDCLK = 1. WDTOF bit is logic 1 after Watchdog reset and is logic 0 after power-on reset. Other resets will not affect WDTOF. On power-on reset, the TRIM SFR is initialized with a factory preprogrammed value. Other resets will not cause initialization of the TRIM register. The only reset source that affects these SFRs is power-on reset.
P89LPC915/916/917
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
9. Functional description
Remark: Please refer to the P89LPC915/916/917 User's Manual for a more detailed functional description.
9.1 Enhanced CPU
The P89LPC915/916/917 uses an enhanced 80C51 CPU which runs at 6 times the speed of standard 80C51 devices. A machine cycle consists of two CPU clock cycles, and most instructions execute in one or two machine cycles.
9.2 Clocks
9.2.1 Clock definitions The P89LPC915/916/917 device has several internal clocks as defined below: OSCCLK -- Input to the DIVM clock divider. OSCCLK is selected from one of three clock sources (see Figure 10) and can also be optionally divided to a slower frequency (see Section 9.7 "CPU Clock (CCLK) modification: DIVM register"). Note: fosc is defined as the OSCCLK frequency. CCLK -- CPU clock; output of the clock divider. There are two CCLK cycles per machine cycle, and most instructions are executed in one to two machine cycles (two or four CCLK cycles). RCCLK -- The internal 7.373 MHz RC oscillator output. PCLK -- Clock for the various peripheral devices and is CCLK/2 9.2.2 CPU clock (OSCCLK) The P89LPC915/916/917 provide user-selectable oscillator options in generating the CPU clock. This allows optimization for a range of needs from high precision to lowest possible cost. These options are configured when the FLASH is programmed and include an on-chip Watchdog oscillator, an on-chip RC oscillator, and an external clock input. 9.2.3 Clock output (P89LPC917) The P89LPC917 supports a user selectable clock output function on the CLKOUT pin. This allows external devices to synchronize to the P89LPC917. This output is enabled by the ENCLK bit in the TRIM register. The frequency of this clock output is 1 that of the CCLK. If the clock output is not needed in Idle mode, it may be turned 2 off prior to entering Idle, saving additional power.
9.3 On-chip RC oscillator option
The P89LPC915/916/917 has a 6-bit TRIM register that can be used to tune the frequency of the RC oscillator. During reset, the TRIM value is initialized to a factory pre-programmed value to adjust the oscillator frequency to 7.373 MHz, 1 % at room temperature. End-user applications can write to the TRIM register to adjust the on-chip RC oscillator to other frequencies.
9397 750 14397
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
29 of 72
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
9.4 Watchdog oscillator option
The Watchdog has a separate oscillator which has a frequency of 400 kHz. This oscillator can be used to save power when a high clock frequency is not needed.
9.5 External clock input option
In this configuration, the processor clock is derived from an external source driving the CLKIN pin. The rate may be from 0 Hz up to 18 MHz. When using an oscillator frequency above 12 MHz, the reset input function of P1.5 must be enabled. An external circuit is required to hold the device in reset at power-up until VDD has reached its specified level. When system power is removed VDD will fall below the minimum specified operating voltage. When using an oscillator frequency above 12 MHz, in some applications, an external brownout detect circuit may be required to hold the device in reset when VDD falls below the minimum specified operating voltage.
RTCS1:0 XCLK RTC RCCLK CLKIN RCCLK ADC1/DAC1 /2 PCLK WATCHDOG OSCILLATOR (400 kHz) WDT peripheral clock PCLK OSCCLK DIVM RC OSCILLATOR (7.3728 MHz) CCLK CPU CLKOUT
BAUD RATE GENERATOR
UART
TIMERS 1 & 0
I2C
SPI (P89LPC916)
002aaa831
Fig 10. Block diagram of oscillator control.
9.6 CPU Clock (CCLK) wake-up delay
The P89LPC915/916/917 has an internal wake-up timer that delays the clock until it stabilizes. The delay is 224 OSCCLK cycles plus 60 to 100 s.
9.7 CPU Clock (CCLK) modification: DIVM register
The OSCCLK frequency can be divided down up to 510 times by configuring a dividing register, DIVM, to generate CCLK. This feature makes it possible to temporarily run the CPU at a lower rate, reducing power consumption. By dividing the clock, the CPU can retain the ability to respond to events that would not exit Idle mode by executing its normal program at a lower rate. This can also allow bypassing
9397 750 14397 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
30 of 72
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
the oscillator start-up time in cases where Power-down mode would otherwise be used. The value of DIVM may be changed by the program at any time without interrupting code execution.
9.8 Low power select
The P89LPC915/916/917 are designed to run at 18 MHz (CCLK) maximum. However, if CCLK is 8 MHz or slower, the CLKLP SFR bit (AUXR1.7) can be set to logic 1 to lower the power consumption further. On any reset, CLKLP is logic 0 allowing highest performance access. This bit can then be set in software if CCLK is running at 8 MHz or slower.
9397 750 14397
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
31 of 72
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
9.9 A/D converter
9.9.1 General description The P89LPC915/916/917 has an 8-bit, 4-channel multiplexed successive approximation analog-to-digital converter. A block diagram of the A/D converter is shown in Figure 11. The A/D consists of a 4-input multiplexer which feeds a sample-and-hold circuit providing an input signal to one of two comparator inputs. The control logic in combination with the successive approximation register (SAR) drives a digital-to-analog converter which provides the other input to the comparator. The output of the comparator is fed to the SAR.
COMP INPUT MUX + SAR - CONTROL LOGIC
DAC1
8
CCLK
002aaa783
Fig 11. ADC block diagram.
9397 750 14397
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
32 of 72
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
9.9.2
Features
* An 8-bit, 4-channel multiplexed input, successive approximation A/D converter * Four A/D result registers * Six operating modes
- Fixed channel, single conversion mode - Fixed channel, continuous conversion mode - Auto scan, single conversion mode - Auto scan, continuous conversion mode - Dual channel, continuous conversion mode - Single step mode
* Three conversion start modes
- Timer triggered start - Start immediately - Edge triggered
* * * * * *
9.9.3
8-bit conversion time of 3.9 s at an ADC clock of 3.3 MHz Interrupt or polled operation Boundary limits interrupt DAC output to a port pin with high output impedance Clock divider Power-down mode
A/D operating modes Fixed channel, single conversion mode: A single input channel can be selected for conversion. A single conversion will be performed and the result placed in the result register which corresponds to the selected input channel. An interrupt, if enabled, will be generated after the conversion completes. Fixed channel, continuous conversion mode: A single input channel can be selected for continuous conversion. The results of the conversions will be sequentially placed in the four result registers. An interrupt, if enabled, will be generated after every four conversions. Additional conversion results will again cycle through the four result registers, overwriting the previous results. Continuous conversions continue until terminated by the user. Auto scan, single conversion mode: Any combination of the four input channels can be selected for conversion. A single conversion of each selected input will be performed and the result placed in the result register which corresponds to the selected input channel. An interrupt, if enabled, will be generated after all selected channels have been converted. If only a single channel is selected this is equivalent to single channel, single conversion mode. Auto scan, continuous conversion mode: Any combination of the four input channels can be selected for conversion. A conversion of each selected input will be performed and the result placed in the result register which corresponds to the selected input channel. An interrupt, if enabled, will be generated after all selected
9397 750 14397
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
33 of 72
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
channels have been converted. The process will repeat starting with the first selected channel. Additional conversion results will again cycle through the four result registers, overwriting the previous results. Continous conversions continue until terminated by the user. Dual channel, continuous conversion mode: This is a variation of the auto scan continuous conversion mode where conversion occurs on two user-selectable inputs. The result of the conversion of the first channel is placed in result register, AD1DAT0. The result of the conversion of the second channel is placed in result register, AD1DAT1. The first channel is again converted and its result stored in AD1DAT2. The second channel is again converted and its result placed in AD1DAT3. An interrupt is generated, if enabled, after every set of four conversions (two conversions per channel). Single step mode: This special mode allows `single-stepping' in an auto scan conversion mode. Any combination of the four input channels can be selected for conversion. After each channel is converted, an interrupt is generated, if enabled, and the A/D waits for the next start condition. May be used with any of the start modes. 9.9.4 Conversion start modes Timer triggered start: An A/D conversion is started by the overflow of Timer 0. Once a conversion has started, additional Timer 0 triggers are ignored until the conversion has completed. The Timer triggered start mode is available in all A/D operating modes. Start immediately: Programming this mode immediately starts a conversion. This start mode is available in all A/D operating modes. Edge triggered: (P89LPC915/917) An A/D conversion is started by rising or falling edge of P1.4. Once a conversion has started, additional edge triggers are ignored until the conversion has completed. The edge triggered start mode is available in all A/D operating modes.
9397 750 14397
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
34 of 72
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
9.9.5
Boundary limits interrupt The A/D converters have both a high and low boundary limit register. After the four MSBs have been converted, these four bits are compared with the four MSBs of the boundary high and low registers. If the four MSBs of the conversion are outside the limit an interrupt will be generated, if enabled. If the conversion result is within the limits, the boundary limits will again be compared after all 8 bits have been converted. An interrupt will be generated, if enabled, if the result is outside the boundary limits. The boundary limit may be disabled by clearing the boundary limit interrupt enable.
9.9.6
DAC output to a port pin with high output impedance The A/D converter's DAC block can be output to a port pin. In this mode, the AD1DAT3 register is used to hold the value fed to the DAC. After a value has been written to AD1DAT3, the DAC output will appear on the channel 3 pin.
9.9.7
Clock divider The A/D converter requires that its internal clock source be in the range of 500 kHz to 3.3 MHz to maintain accuracy. A programmable clock divider that divides the clock from 1 to 8 is provided for this purpose.
9.9.8
Power-down and Idle mode In Idle mode the A/D converter, if enabled, will continue to function and can cause the device to exit Idle mode when the conversion is completed if the A/D interrupt is enabled. In Power-down mode or Total power-down mode, the A/D does not function. If the A/D is enabled, it will consume power. Power can be reduced by disabling the A/D.
9.10 Memory organization
The various P89LPC915/916/917 memory spaces are as follows:
* DATA
256 bytes of internal data memory space (00h:FFh) accessed via direct or indirect addressing, using instructions other than MOVX and MOVC. All or part of the Stack may be in this area.
* SFR
Special Function Registers. Selected CPU registers and peripheral control and status registers, accessible only via direct addressing.
* CODE
64 kB of Code memory space, accessed as part of program execution and via the MOVC instruction. The P89LPC915/916/917 has 2 kB of on-chip Code memory.
9.11 Interrupts
The P89LPC915/916/917 uses a four priority level interrupt structure. This allows great flexibility in controlling the handling of the many interrupt sources. The P89LPC915 and P89LPC917 support 13 interrupt sources: external interrupts 0 and 1, timers 0 and 1, serial port Tx, serial port Rx, combined serial port Rx and Tx, brownout detect, Watchdog/Real-Time clock, I2C, keyboard, comparators 1 and 2, and the A/D converter.
9397 750 14397 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
35 of 72
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
The P89LPC916supports 14 interrupt sources: external interrupt 0, timers 0 and 1, serial port Tx, serial port Rx, combined serial port Rx and Tx, brownout detect, Watchdog/Real-Time clock, I2C, keyboard, comparators 1 and 2, SPI, and the A/D converter. Each interrupt source can be individually enabled or disabled by setting or clearing a bit in the interrupt enable registers IEN0 or IEN1. The IEN0 register also contains a global disable bit, EA, which disables all interrupts. Each interrupt source can be individually programmed to one of four priority levels by setting or clearing bits in the interrupt priority registers IP0, IP0H, IP1, and IP1H. An interrupt service routine in progress can be interrupted by a higher priority interrupt, but not by another interrupt of the same or lower priority. The highest priority interrupt service cannot be interrupted by any other interrupt source. If two requests of different priority levels are pending at the start of an instruction, the request of higher priority level is serviced. If requests of the same priority level are pending at the start of an instruction, an internal polling sequence determines which request is serviced. This is called the arbitration ranking. Note that the arbitration ranking is only used to resolve pending requests of the same priority level. 9.11.1 External interrupt inputs The P89LPC915 and P89LPC917 have two external interrupt inputs as well as the Keypad Interrupt function. The P89LPC916 has one external interrupt input as well as the Keypad Interrupt function These external interrupt inputs are identical to those present on the standard 80C51 microcontrollers. These external interrupts can be programmed to be level-triggered or edge-triggered by setting or clearing bit IT1 or IT0 in Register TCON. In edge-triggered mode, if successive samples of the INTn pin show a HIGH in one cycle and a LOW in the next cycle, the interrupt request flag IEn in TCON is set, causing an interrupt request. If an external interrupt is enabled when the P89LPC915/916/917 is put into Power-down or Idle mode, the interrupt will cause the processor to wake-up and resume operation. Refer to Section 9.14 "Power reduction modes" for details.
9397 750 14397
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
36 of 72
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
IE0 EX0 (P89LPC915/917) IE1 EX1 BOF EBO RTCF ERTC (RTCCON.1) WDOVF KBIF EKBI EWDRT CMF2 CMF1 EC EA (IE0.7) TF0 ET0 TF1 ET1 TI & RI/RI ES/ESR TI EST SI EI2C (P89LPC916) SPIF ESPI INTERRUPT TO CPU WAKE-UP (IF IN POWER-DOWN)
ENADCI1 ADCI1 ENBI1 BNDI1 EAD
002aaa833
Fig 12. Interrupt sources, interrupt enables, and power-down wake-up sources.
9397 750 14397
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
37 of 72
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
9.12 I/O ports
The P89LPC916 and P89LPC917 devices have three I/O ports: Port 0, Port 1, and Port 2. The exact number of I/O pins available depends on the clock and reset options chosen, as shown in Table 10.
Table 10: Number of I/O pins available (P89LPC916, P89LPC917) Reset option Number of I/O pins (16-pin package) 14 13 13 12
Clock source
RC oscillator or Watchdog oscillator No external reset (except during power-up) External RST pin supported External clock input No external reset (except during power-up) External RST pin supported[1]
[1] Required for operation above 12 MHz.
The P89LPC915 has 2I/O ports: Port 0, and Port 1. The exact number of I/O pins available depends on the reset option chosen, as shown in Table 11.
Table 11: Number of I/O pins available (P89LPC915) Reset option Number of I/O pins (14-pin package) 12 11 11 10
Clock source
RC oscillator or Watchdog oscillator No external reset (except during power-up) External RST pin supported External clock input No external reset (except during power-up) External RST pin supported[1]
[1] Required for operation above 12 MHz.
9.12.1
Port configurations Except as listed below, every I/O pin on the P89LPC915/916/917 may be configured by software to one of four types on a bit-by-bit basis. These are: quasi-bidirectional (standard 80C51 port outputs), push-pull, open drain, and input-only. Two configuration registers for each port select the output type for each port pin. P1.5/RST can only be an input and cannot be configured. SCL/T0/P1.2 and SDA/INTO/P1.3 may only be configured to be either input-only or open drain.
9.12.2
Quasi-bidirectional output configuration Quasi-bidirectional output type can be used as both an input and output without the need to reconfigure the port. This is possible because when the port outputs a logic HIGH, it is weakly driven, allowing an external device to pull the pin LOW. When the
9397 750 14397
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
38 of 72
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
pin is driven LOW, it is driven strongly and able to sink a fairly large current. These features are somewhat similar to an open-drain output except that there are three pull-up transistors in the quasi-bidirectional output that serve different purposes. The P89LPC915/916/917 is a 3 V device, but the pins are 5 V-tolerant. In quasi-bidirectional mode, if a user applies 5 V on the pin, there will be a current flowing from the pin to VDD, causing extra power consumption. Therefore, applying 5 V in quasi-bidirectional mode is discouraged. A quasi-bidirectional port pin has a Schmitt triggered input that also has a glitch suppression circuit. 9.12.3 Open-drain output configuration The open-drain output configuration turns off all pull-ups and only drives the pull-down transistor of the port driver when the port latch contains a logic 0. To be used as a logic output, a port configured in this manner must have an external pull-up, typically a resistor tied to VDD. An open-drain port pin has a Schmitt triggered input that also has a glitch suppression circuit. 9.12.4 Input-only configuration The input-only port configuration has no output drivers. It is a Schmitt triggered input that also has a glitch suppression circuit. 9.12.5 Push-pull output configuration The push-pull output configuration has the same pull-down structure as both the open-drain and the quasi-bidirectional output modes, but provides a continuous strong pull-up when the port latch contains a logic 1. The push-pull mode may be used when more source current is needed from a port output. A push-pull port pin has a Schmitt triggered input that also has a glitch suppression circuit. 9.12.6 Port 0 analog functions The P89LPC915/916/917 incorporates two Analog Comparators. In order to give the best analog function performance and to minimize power consumption, pins that are being used for analog functions must have the digital outputs and digital inputs disabled. Digital outputs are disabled by putting the port output into the Input-Only (high impedance) mode as described in Section 9.12.4 "Input-only configuration". Digital inputs on Port 0 may be disabled through the use of the PT0AD register. On any reset, the PT0AD bits default to logic 0s to enable digital functions.
9397 750 14397
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
39 of 72
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
9.12.7
Additional port features After power-up, all pins are in Input-Only mode. After power-up all I/O pins except P1.5, may be configured by software.
* Pin P1.5 is input only. * SCL/T0/P1.2 and SDA/INTO/P1.3 may only be configured to be either input-only or
open drain. Every output on the P89LPC915/916/917 has been designed to sink typical LED drive current. However, there is a maximum total output current for all ports which must not be exceeded. Please refer to Table 13 "DC electrical characteristics" for detailed specifications. All port pins that can function as an output have slew rate controlled outputs to limit noise generated by quickly switching output signals. The slew rate is factory-set to approximately 10 ns rise and fall times.
9.13 Power monitoring functions
The P89LPC915/916/917 incorporates power monitoring functions designed to prevent incorrect operation during initial power-up and power loss or reduction during operation. This is accomplished with two hardware functions: Power-on detect and Brownout detect. 9.13.1 Brownout detection The Brownout detect function determines if the power supply voltage drops below a certain level. The default operation is for a Brownout detection to cause a processor reset, however, it may alternatively be configured to generate an interrupt. Brownout detection may be enabled or disabled in software. If Brownout detection is enabled, the brownout condition occurs when VDD falls below the brownout trip voltage, VBO (see Table 13 "DC electrical characteristics"), and is negated when VDD rises above VBO. If the P89LPC915/916/917 device is to operate with a power supply that can be below 2.7 V, BOE should be left in the unprogrammed state so that the device can operate at 2.4 V, otherwise continuous brownout reset may prevent the device from operating. For correct activation of Brownout detect, the VDD rise and fall times must be observed. Please see Table 13 "DC electrical characteristics" for specifications. 9.13.2 Power-on detection The Power-on detect has a function similar to the Brownout detect, but is designed to work as power comes up initially, before the power supply voltage reaches a level where Brownout detect can work. The POF flag in the RSTSRC register is set to indicate an initial power-up condition. The POF flag will remain set until cleared by software.
9.14 Power reduction modes
The P89LPC915/916/917 supports three different power reduction modes. These modes are Idle mode, Power-down mode, and total Power-down mode.
9397 750 14397 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
40 of 72
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
9.14.1
Idle mode Idle mode leaves peripherals running in order to allow them to activate the processor when an interrupt is generated. Any enabled interrupt source or reset may terminate Idle mode.
9.14.2
Power-down mode The Power-down mode stops the oscillator in order to minimize power consumption. The P89LPC915/916/917 exits Power-down mode via any reset, or certain interrupts. In Power-down mode, the power supply voltage may be reduced to the RAM keep-alive voltage VRAM. This retains the RAM contents at the point where Power-down mode was entered. SFR contents are not guaranteed after VDD has been lowered to VRAM, therefore it is highly recommended to wake up the processor via reset in this case. VDD must be raised to within the operating range before the Power-down mode is exited. Some chip functions continue to operate and draw power during Power-down mode, increasing the total power used during power-down. These include: Brownout detect, Watchdog Timer, Comparators (note that Comparators can be powered-down separately), and Real-Time Clock (RTC)/System Timer. The internal RC oscillator is disabled unless both the RC oscillator has been selected as the system clock and the RTC is enabled.
9.14.3
Total Power-down mode This is the same as Power-down mode except that the brownout detection circuitry and the voltage comparators are also disabled to conserve additional power. The internal RC oscillator is disabled unless both the RC oscillator has been selected as the system clock and the RTC is enabled. If the internal RC oscillator is used to clock the RTC during Power-down, there will be high power consumption. Please use an external low frequency clock to achieve low power with the Real-Time Clock running during Power-down.
9.15 Reset
The P1.5/RST pin can function as either an active-LOW reset input or as a digital input, P1.5. The RPE (Reset Pin Enable) bit in UCFG1, when set to logic 1, enables the external reset input function on P1.5. When cleared, P1.5 may be used as an input pin. Remark: During a power-up sequence, the RPE selection is overridden and this pin will always function as a reset input. An external circuit connected to this pin should not hold this pin LOW during a power-on sequence as this will keep the device in reset. After power-up this input will function either as an external reset input or as a digital input as defined by the RPE bit. Only a power-up reset will temporarily override the selection defined by RPE bit. Other sources of reset will not override the RPE bit.
9397 750 14397
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
41 of 72
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
Reset can be triggered from the following sources:
* External reset pin (during power-up or if user configured via UCFG1. This option
must be used for an oscillator frequency above 12 MHz.)
* * * * *
Power-on detect Brownout detect Watchdog Timer Software reset UART break character detect reset.
For every reset source, there is a flag in the Reset Register, RSTSRC. The user can read this register to determine the most recent reset source. These flag bits can be cleared in software by writing a logic 0 to the corresponding bit. More than one flag bit may be set:
* During a power-on reset, both POF and BOF are set but the other flag bits are
cleared.
* For any other reset, previously set flag bits that have not been cleared will remain
set.
9.16 Timers/counters 0 and 1
The P89LPC915/916/917 devices have two general purpose counter/timers which are upward compatible with the standard 80C51 Timer 0 and Timer 1. An option to automatically toggle the T0 pin upon timer overflow has been added. In addition an option to toggle the T1 pin upon overflow has been added on the P89LPC917. In the `Timer' function, the register is incremented every machine cycle. In the `Counter' function, the register of Timer 0 is incremented in response to a 1-to-0 transition at its external input pin. This external input is sampled once very machine cycle. Timer 0 has five operating modes (modes 0, 1, 2, 3, and 6). Timer 1 has four operating modes (modes 0, 1, 2, and 3), except on the P89LPC917 where Timer 1 also has mode 6. Modes 0, 1, and 2 are the same for both Timers/Counters. Mode 3 is different. 9.16.1 Mode 0 Putting either Timer into Mode 0 makes it look like an 8048 Timer, which is an 8-bit Counter with a divide-by-32 prescaler. In this mode, the Timer register is configured as a 13-bit register. Mode 0 operation is the same for Timer 0 and Timer 1. 9.16.2 Mode 1 Mode 1 is the same as Mode 0, except that all 16 bits of the timer register are used. 9.16.3 Mode 2 Mode 2 configures the Timer register as an 8-bit Counter with automatic reload. Mode 2 operation is the same for Timer 0 and Timer 1.
9397 750 14397
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
42 of 72
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
9.16.4
Mode 3 When Timer 1 is in Mode 3 it is stopped. Timer 0 in Mode 3 forms two separate 8-bit counters and is provided for applications that require an extra 8-bit timer. When Timer 1 is in Mode 3 it can still be used by the serial port as a baud rate generator.
9.16.5
Mode 6 In this mode, the corresponding timer can be changed to a PWM with a full period of 256 timer clocks.
9.16.6
Timer overflow toggle output Timer 0 (and Timer 1 on the P89LPC917) can be configured to automatically toggle the timer output pin, Tx, whenever a timer overflow occurs. The same device pin that is used for the count input is also used for the timer toggle output. The port output will be a logic 1 prior to the first timer overflow when this mode is turned on.
9.17 Real-Time clock/system timer
The P89LPC915/916/917 devices have a simple Real-Time clock that allows a user to continue running an accurate timer while the rest of the device is powered-down. The Real-Time clock can be a wake-up or an interrupt source. The Real-Time clock is a 23-bit down counter comprised of a 7-bit prescaler and a 16-bit loadable down counter. When it reaches all logic 0s, the counter will be reloaded again and the RTCF flag will be set. The clock source for this counter can either be the CPU clock (CCLK) or the external clock input, provided that the external clock input is not being used as the CPU clock. If the external clock input is used as the CPU clock, then the RTC will use CCLK as its clock source. Only power-on reset will reset the Real-Time clock and its associated SFRs to the default state.
9.18 UART
The P89LPC915/916/917 has an enhanced UART that is compatible with the conventional 80C51 UART except that Timer 2 overflow cannot be used as a baud rate source. The P89LPC915/916/917 does include an independent Baud Rate Generator. The baud rate can be selected from CCLK (divided by a constant), Timer 1 overflow, or the independent Baud Rate Generator. In addition to the baud rate generation, enhancements over the standard 80C51 UART include Framing Error detection, automatic address recognition, selectable double buffering and several interrupt options. The UART can be operated in 4 modes: shift register, 8-bit UART, 9-bit UART, and CCLK/32 or CCLK/16. 9.18.1 Mode 0 Serial data enters and exits through RxD. TxD outputs the shift clock. 8 bits are transmitted or received, LSB first. The baud rate is fixed at 116 of the CPU clock frequency.
9397 750 14397
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
43 of 72
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
9.18.2
Mode 1 10 bits are transmitted (through TxD) or received (through RxD): a start bit (logic 0), 8 data bits (LSB first), and a stop bit (logic 1). When data is received, the stop bit is stored in RB8 in Special Function Register SCON. The baud rate is variable and is determined by the Timer 1 overflow rate or the Baud Rate Generator (described in Section 9.18.5 "Baud rate generator and selection").
9.18.3
Mode 2 11 bits are transmitted (through TxD) or received (through RxD): start bit (logic 0), 8 data bits (LSB first), a programmable 9th data bit, and a stop bit (logic 1). When data is transmitted, the 9th data bit (TB8 in SCON) can be assigned the value of logic 0 or 1. Or, for example, the parity bit (P, in the PSW) could be moved into TB8. When data is received, the 9th data bit goes into RB8 in Special Function Register SCON, while the stop bit is not saved. The baud rate is programmable to either 116 or 1 of the CCLK frequency, as determined by the SMOD1 bit in PCON. 32
9.18.4
Mode 3 11 bits are transmitted (through TxD) or received (through RxD): a start bit (logic 0), 8 data bits (LSB first), a programmable 9th data bit, and a stop bit (logic 1). In fact, Mode 3 is the same as Mode 2 in all respects except baud rate. The baud rate in Mode 3 is variable and is determined by the Timer 1 overflow rate or the Baud Rate Generator (described in section Section 9.18.5 "Baud rate generator and selection").
9.18.5
Baud rate generator and selection The P89LPC915/916/917 has an independent Baud Rate Generator. The baud rate is determined by a baud-rate preprogrammed into the BRGR1 and BRGR0 SFRs which together form a 16-bit baud rate divisor value that works in a similar manner as Timer 1. If the baud rate generator is used, Timer 1 can be used for other timing functions. The UART can use either Timer 1 or the baud rate generator output (see Figure 13). Note that Timer T1 is further divided by 2 if the SMOD1 bit (PCON.7) is cleared. The independent Baud Rate Generator uses CCLK.
Timer 1 Overflow (PCLK-based) Baud Rate Generator (CCLK-based)
SMOD1 = 1
SBRGS = 0 Baud Rate Modes 1 and 3
2
SMOD1 = 0
SBRGS = 1
002aaa419
Fig 13. Baud rate sources for UART (Modes 1, 3).
9.18.6
Framing error Framing error is reported in the status register (SSTAT). In addition, if SMOD0 (PCON.6) is logic 1, framing errors can be made available in SCON.7, respectively. If SMOD0 is logic 0, SCON.7 is SM0. It is recommended that SM0 and SM1 (SCON.7:6) are set up when SMOD0 is logic 0.
9397 750 14397
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
44 of 72
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
9.18.7
Break detect Break detect is reported in the status register (SSTAT). A break is detected when 11 consecutive bits are sensed LOW. The break detect can be used to reset the device.
9.18.8
Double buffering The UART has a transmit double buffer that allows buffering of the next character to be written to SBUF while the first character is being transmitted. Double buffering allows transmission of a string of characters with only one stop bit between any two characters, as long as the next character is written between the start bit and the stop bit of the previous character. Double buffering can be disabled. If disabled (DBMOD, i.e., SSTAT.7 = 0), the UART is compatible with the conventional 80C51 UART. If enabled, the UART allows writing to SnBUF while the previous data is being shifted out. Double buffering is only allowed in Modes 1, 2 and 3. When operated in Mode 0, double buffering must be disabled (DBMOD = 0).
9.18.9
Transmit interrupts with double buffering enabled (Modes 1, 2 and 3) Unlike the conventional UART, in double buffering mode, the Tx interrupt is generated when the double buffer is ready to receive new data.
9.18.10
The 9th bit (bit 8) in double buffering (Modes 1, 2 and 3) If double buffering is disabled TB8 can be written before or after SBUF is written, as long as TB8 is updated some time before that bit is shifted out. TB8 must not be changed until the bit is shifted out, as indicated by the Tx interrupt. If double buffering is enabled, TB8 must be updated before SBUF is written, as TB8 will be double-buffered together with SBUF data.
9397 750 14397
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
45 of 72
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
9.19 I2C-bus serial interface
I2C-bus uses two wires (SDA and SCL) to transfer information between devices connected to the bus, and it has the following features:
* Bi-directional data transfer between masters and slaves * Multi master bus (no central master) * Arbitration between simultaneously transmitting masters without corruption of
serial data on the bus
* Serial clock synchronization allows devices with different bit rates to communicate
via one serial bus
* Serial clock synchronization can be used as a handshake mechanism to suspend
and resume serial transfer
* The I2C-bus may be used for test and diagnostic purposes.
A typical I2C-bus configuration is shown in Figure 14. The P89LPC915/916/917 device provides a byte-oriented I2C-bus interface that supports data transfers up to 400 kHz.
RP
RP SDA
I2C-BUS SCL P1.3/SDA P1.2/SCL OTHER DEVICE WITH I2C-BUS INTERFACE OTHER DEVICE WITH I2C-BUS INTERFACE
002aaa834
P89LPC915/916/917
Fig 14. I2C-bus configuration.
9397 750 14397
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
46 of 72
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
8
ADDRESS REGISTER P1.3
I2ADR
COMPARATOR INPUT FILTER P1.3/SDA OUTPUT STAGE SHIFT REGISTER 8 ACK I2DAT
INPUT FILTER P1.2/SCL OUTPUT STAGE TIMER 1 OVERFLOW P1.2 I2CON I2SCLH I2SCLL
BIT COUNTER / ARBITRATION & SYNC LOGIC
CCLK TIMING & CONTROL LOGIC INTERRUPT
SERIAL CLOCK GENERATOR
CONTROL REGISTERS & SCL DUTY CYCLE REGISTERS 8
STATUS BUS
STATUS DECODER
I2STAT
STATUS REGISTER
8
002aaa421
Fig 15. I2C-bus serial interface block diagram.
9.20 Serial Peripheral Interface (SPI - P89LPC916)
The P89LPC916 provides another high-speed serial communication interface--the SPI interface. SPI is a full-duplex, high-speed, synchronous communication bus with two operation modes: Master mode and Slave mode. Up to 4.5 Mbit/s can be supported in either Master or 3.0 Mbit/s in Slave mode. It has a Transfer Completion Flag and Write Collision Flag Protection.
9397 750 14397
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
47 of 72
INTERNAL BUS
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
S M PIN CONTROL LOGIC CPU clock 8-BIT SHIFT REGISTER DIVIDER BY 4, 16, 64, 128 READ DATA BUFFER M S
MISO P2.3 MOSI P2.2 SPICLK P2.5 SS P2.4 SPEN
SPI clock (master) SELECT SPR1 SPR0
clock CLOCK LOGIC S M MSTR DORD MSTR CPHA SPEN CPOL SPR1 SPI CONTROL REGISTER internal data bus SPR0 SSIG
SPI CONTROL WCOL SPIF
MSTR SPEN
SPI STATUS REGISTER
SPI interrupt request
002aaa497
Fig 16. SPI block diagram (P89LPC916).
The SPI interface has four pins: SPICLK, MOSI, MISO, and SS:
* SPICLK, MOSI and MISO are typically tied together between two or more SPI
devices. Data flows from master to slave on MOSI (Master Out Slave In) pin and flows from slave to master on MISO (Master In Slave Out) pin. The SPICLK signal is output in the master mode and is input in the slave mode. If the SPI system is disabled, i.e., SPEN (SPCTL.6) = 0 (reset value), these pins are configured for port functions.
* SS is the optional slave select pin. In a typical configuration, an SPI master asserts
one of its port pins to select one SPI device as the current slave. An SPI slave device uses its SS pin to determine whether it is selected. Typical connections are shown in Figure 17, 18, and 19.
9397 750 14397
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
48 of 72
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
9.20.1
Typical SPI configurations
Master MISO 8-BIT SHIFT REGISTER MOSI MISO MOSI
Slave
8-BIT SHIFT REGISTER
SPICLK SPI CLOCK GENERATOR PORT
SPICLK SS
002aaa435
Fig 17. SPI single master single slave configuration.
Master MISO 8-BIT SHIFT REGISTER MOSI MISO MOSI
Slave
8-BIT SHIFT REGISTER
SPICLK SPI CLOCK GENERATOR port
SPICLK SS
Slave MISO MOSI 8-BIT SHIFT REGISTER
SPICLK port SS
002aaa437
Fig 18. SPI single master multiple slaves configuration.
9397 750 14397
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
49 of 72
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
Master MISO 8-BIT SHIFT REGISTER MOSI MISO MOSI
Slave
8-BIT SHIFT REGISTER
SPICLK SPI CLOCK GENERATOR SS
SPICLK SS SPI CLOCK GENERATOR
002aaa499
Fig 19. SPI dual device configuration, where either can be a master or a slave.
9397 750 14397
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
50 of 72
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
9.21 Analog comparators
Two analog comparators are provided on the P89LPC915/916/917. Input and output options allow use of the comparators in a number of different configurations. Comparator operation is such that the output is a logic 1 when the positive input is greater than the negative input (selectable from a pin or an internal reference voltage). Otherwise the output is a zero. Each comparator may be configured to cause an interrupt when the output value changes. Comparator 1 may be output to a port pin. The overall connections to both comparators are shown in Figure 20. The comparators function to VDD = 2.4 V. When each comparator is first enabled, the comparator output and interrupt flag are not guaranteed to be stable for 10 microseconds. The corresponding comparator interrupt should not be enabled during that time, and the comparator interrupt flag must be cleared before the interrupt is enabled in order to prevent an immediate interrupt service.
CP1 (P0.4) CIN1A (P0.3) CIN1B (P0.5) CMPREF VREF CN1
Comparator 1
CO1 Change Detect CMF1
Interrupt Change Detect CP2 (P0.2) CIN2A (P0.1) CIN2B CMP2 (P0.0) CO2 OE2 CN2 (P89LPC915/917)
002aaa835
EC CMF2
Comparator 2
Fig 20. Comparator input and output connections.
9.22 Internal reference voltage
An internal reference voltage generator may supply a default reference when a single comparator input pin is used. The value of the internal reference voltage, referred to as VREF, is 1.23 V 10 %.
9.23 Comparator interrupt
Each comparator has an interrupt flag contained in its configuration register. This flag is set whenever the comparator output changes state. The flag may be polled by software or may be used to generate an interrupt. The two comparators use one common interrupt vector. If both comparators enable interrupts, after entering the interrupt service routine, the user needs to read the flags to determine which comparator caused the interrupt.
9397 750 14397
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
51 of 72
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
Possible comparator configurations are shown in Figure 20.
9.24 Comparator and power reduction modes
Either or both comparators may remain enabled when Power-down or Idle mode is activated, but both comparators are disabled automatically in Total Power-down mode. If a comparator interrupt is enabled (except in Total Power-down mode), a change of the comparator output state will generate an interrupt and wake up the processor. If the comparator output to a pin is enabled, the pin should be configured in the push-pull mode in order to obtain fast switching times while in Power-down mode. The reason is that with the oscillator stopped, the temporary strong pull-up that normally occurs during switching on a quasi-bidirectional port pin does not take place. Comparators consume power in Power-down and Idle modes, as well as in the normal operating mode. This fact should be taken into account when system power consumption is an issue. To minimize power consumption, the user can disable the comparators via PCONA.5, or put the device in Total Power-down mode.
9.25 Keypad interrupt (KBI)
The Keypad Interrupt function is intended primarily to allow a single interrupt to be generated when Port 0 is equal to or not equal to a certain pattern. This function can be used for bus address recognition or keypad recognition. The user can configure the port via SFRs for different tasks. The Keypad Interrupt Mask Register (KBMASK) is used to define which input pins connected to Port 0 can trigger the interrupt. The Keypad Pattern Register (KBPATN) is used to define a pattern that is compared to the value of Port 0. The Keypad Interrupt Flag (KBIF) in the Keypad Interrupt Control Register (KBCON) is set when the condition is matched while the Keypad Interrupt function is active. An interrupt will be generated if enabled. The PATN_SEL bit in the Keypad Interrupt Control Register (KBCON) is used to define equal or not-equal for the comparison. In order to use the Keypad Interrupt as an original KBI function like in 87LPC76x series, the user needs to set KBPATN = 0FFH and PATN_SEL = 1 (not equal), then any key connected to Port 0 which is enabled by the KBMASK register will cause the hardware to set KBIF and generate an interrupt if it has been enabled. The interrupt may be used to wake up the CPU from Idle or Power-down modes. This feature is particularly useful in handheld, battery-powered systems that need to carefully manage power consumption yet also need to be convenient to use. In order to set the flag and cause an interrupt, the pattern on Port 0 must be held longer than six CCLKs.
9.26 Watchdog timer
The Watchdog timer causes a system reset when it underflows as a result of a failure to feed the timer prior to the timer reaching its terminal count. It consists of a programmable 12-bit prescaler, and an 8-bit down counter. The down counter is decremented by a tap taken from the prescaler. The clock source for the prescaler is either the PCLK or the nominal 400 kHz Watchdog oscillator. The Watchdog timer
9397 750 14397 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
52 of 72
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
can only be reset by a power-on reset. When the Watchdog feature is disabled, it can be used as an interval timer and may generate an interrupt. Figure 21 shows the Watchdog timer in Watchdog mode. Feeding the Watchdog requires a two-byte sequence. If PCLK is selected as the Watchdog clock and the CPU is powered-down, the Watchdog is disabled. The Watchdog timer has a time-out period that ranges from a few s to a few seconds. Please refer to the P89LPC915/916/917 User's Manual for more details.
WDL (C1H)
MOV WFEED1, #0A5H MOV WFEED2, #05AH Watchdog oscillator PCLK
/32
PRESCALER
8-BIT DOWN COUNTER
RESET see note (1)
CONTROL REGISTER
SHADOW REGISTER FOR WDCON
WDCON (A7H)
PRE2
PRE1
PRE0
-
-
WDRUN
WDTOF
WDCLK
002aaa423
(1) Watchdog reset can also be caused by an invalid feed sequence, or by writing to WDCON not immediately followed by a feed sequence.
Fig 21. Watchdog timer in Watchdog mode (WDTE = 1).
9.27 Additional features
9.27.1 Software reset The SRST bit in AUXR1 gives software the opportunity to reset the processor completely, as if an external reset or Watchdog reset had occurred. Care should be taken when writing to AUXR1 to avoid accidental software resets. 9.27.2 Dual data pointers The dual Data Pointers (DPTR) provides two different Data Pointers to specify the address used with certain instructions. The DPS bit in the AUXR1 register selects one of the two Data Pointers. Bit 2 of AUXR1 is permanently wired as a logic 0 so that the DPS bit may be toggled (thereby switching Data Pointers) simply by incrementing the AUXR1 register, without the possibility of inadvertently altering other bits in the register.
9.28 Flash program memory
9.28.1 General description The P89LPC915/916/917 Flash memory provides in-circuit electrical erasure and programming. The Flash can be erased, read, and written as bytes. The Sector and Page Erase functions can erase any Flash sector (256 bytes) or page (16 bytes). The
9397 750 14397 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
53 of 72
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
Chip Erase operation will erase the entire program memory. In-Circuit Programming using standard commercial programmers is available. In addition, In-Application Programming (IAP-Lite) and byte erase allows code memory to be used for non-volatile data storage. On-chip erase and write timing generation contribute to a user-friendly programming interface. The P89LPC915/916/917 Flash reliably stores memory contents even after 100,000 erase and program cycles. The cell is designed to optimize the erase and programming mechanisms. The P89LPC915/916/917 uses VDD as the supply voltage to perform the Program/Erase algorithms. 9.28.2 Features
* * * * * * * *
9.28.3
Programming and erase over the full operating voltage range. Byte-erase allowing code memory to be used for data storage. Read/Programming/Erase using ICP. Any flash program operation in 4 ms. Programming with industry-standard commercial programmers. Programmable security for the code in the Flash for each sector. More than 100,000 minimum erase/program cycles for each byte. 10-year minimum data retention.
Flash organization The P89LPC915/916/917 program memory consists of eight 256- byte sectors. Each sector can be further divided into sixteen 16-byte pages. In addition to sector erase, page erase, and byte erase, a 16-byte page register is included which allows from 1 to 16 bytes of a given page to be programmed at the same time, substantially reducing overall programming time. In addition, erasing and reprogramming of user-programmable configuration bytes including UCFG1, the Boot Status Bit, and the Boot Vector is supported.
9.28.4
Flash programming and erasing Different methods of erasing or programming of the Flash are available. The Flash may be programmed or erased in the end-user application (IAP-Lite) under control of the application's firmware. Another option is to use the In-Circuit Programming (ICP) mechanism. This ICP system provides for programming through a serial clock- serial data interface using a commercially available EPROM programmer which supports this device. This device does not provide for direct verification of code memory contents. Instead this device provides a 32-bit CRC result on either a sector or the entire 2 kB of user code space.
9.28.5
In-circuit programming (ICP) In-Circuit Programming is performed without removing the microcontroller from the system. The In-Circuit Programming facility consists of internal hardware resources to facilitate remote programming of the P89LPC915/916/917 through a two-wire serial interface. The Philips In-Circuit Programming facility has made in-circuit programming in an embedded application, using commercially available programmers, possible with a minimum of additional expense in components and circuit board area. The ICP function uses five pins. Only a small connector (with VDD,
9397 750 14397
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
54 of 72
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
VSS, RST, clock, and data signals) needs to be available to interface your application to a commercial programmer in order to use this feature. Additional details may be found in the P89LPC915/916/917 User's Manual. 9.28.6 In-application programming (IAP-Lite) In-Application Programming is performed in the application under the control of the microcontroller's firmware. The IAP-Lite facility consists of internal hardware resources to facilitate programming and erasing. The Philips In-Application Programming Lite has made in-application programming in an embedded application possible without additional components. This is accomplished through the use of four SFRs consisting of a control/status register, a data register, and two address registers. Additional details may be found in the P89LPC915/916/917 User's Manual. 9.28.7 Using flash as data storage The Flash code memory array of this device supports individual byte erasing and programming. Any byte in the code memory array may be read using the MOVC instruction, provided that the sector containing the byte has not been secured (a MOVC instruction is not allowed to read code memory contents of a secured sector). Thus any byte in a non-secured sector may be used for non-volatile data storage. 9.28.8 User configuration bytes Some user-configurable features of the P89LPC915/916/917 must be defined at power-up and therefore cannot be set by the program after start of execution. These features are configured through the use of the Flash byte UCFG1. Please see the P89LPC915/916/917 User's Manual for additional details. 9.28.9 User sector security bytes There are eight User Sector Security Bytes, each corresponding to one sector. Please see the P89LPC915/916/917 User's Manual for additional details.
9397 750 14397
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
55 of 72
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
10. Limiting values
Table 12: Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134).[1] Symbol Tamb(bias) Tstg Vn IOH(I/O) IOL(I/O) II/O(tot)(max) Ptot(pack) Parameter operating bias ambient temperature storage temperature range voltage on any pin to VSS high-level output current per I/O pin low-level output current per I/O pin maximum total I/O current total power dissipation per package based on package heat transfer, not device power consumption Conditions Min -55 -65 -0.5 Max +125 +150 +5.5 8 20 120 1.5 Unit C C V mA mA mA W
[1]
The following applies to Limiting values: a) Stresses above those listed under Table 12 may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any conditions other than those described in Table 13 "DC electrical characteristics", Table 14 "AC characteristics"and Table 15 "AC characteristics" of this specification are not implied. b) This product includes circuitry specifically designed for the protection of its internal devices from the damaging effects of excessive static charge. Nonetheless, it is suggested that conventional precautions be taken to avoid applying greater than the rated maximum. c) Parameters are valid over operating temperature range unless otherwise specified. All voltages are with respect to VSS unless otherwise noted.
9397 750 14397
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
56 of 72
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
11. Static characteristics
Table 13: DC electrical characteristics VDD = 2.4 V to 3.6 V unless otherwise specified. Tamb = -40 C to +85 C for industrial, -40 C to +125 C extended, unless otherwise specified. Symbol IDD(oper) IDD(idle) IDD(PD) Parameter power supply current, operating power supply current, Idle mode power supply current, Power-down mode, voltage comparators powered-down power supply current, total Power-down mode Conditions 3.6 V; 12 MHz 3.6 V; 18 MHz 3.6 V; 12 MHz 3.6 V; 18 MHz 3.6 V, industrial 3.6 V, extended 3.6 V, industrial 3.6 V, extended
[2] [2] [2] [2] [2] [2] [2] [2]
Min 1.5 0.22VDD -
Typ[1] 7 11 3.6 4 45 < 0.1 0.4VDD 0.6VDD 0.2VDD 0.6 0.3 0.2 VDD - 0.4 VDD - 0.2 -
Max 13 16 4.8 6 70 150 5 50 2 50 0.7VDD 1.0 0.5 0.3 15 -80 10 -450 30 2.70
Unit mA mA mA mA A A A A mV/s mV/s V V V V V V V V V V pF A A A k V
IDD(TPD)
(dVDD/dt)r VDD rise rate (dVDD/dt)f VRAM Vth(HL) Vth(LH) Vhys VOL VDD fall rate RAM keep-alive voltage negative-going threshold voltage (Schmitt trigger input) positive-going threshold voltage (Schmitt trigger input) hysteresis voltage low-level output voltage, all ports IOL = 20 mA IOL = 10 mA IOL = 3.2 mA VOH high-level output voltage, all ports IOH = -8 mA; push-pull mode IOH = -3.2 mA; push-pull mode IOH = -20 A; quasi-bidirectional mode Cig IIL ILI ITL RRST VBO input-ground capacitance logical 0 input current, all ports logical 1-to-0 transition current, all ports internal reset pull-up resistor brownout trip voltage with BOV = 1, BOPD = 0 2.4 V < VDD < 3.6 V VIN = 0.4 V
[3] [4]
VDD - 1 VDD - 0.7 VDD - 0.3 -30 10 2.40
input leakage current, all ports VIN = VIL or VIH VIN = 2.0 V at VDD = 3.6 V
[5] [6][7]
9397 750 14397
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
57 of 72
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
Table 13: DC electrical characteristics...continued VDD = 2.4 V to 3.6 V unless otherwise specified. Tamb = -40 C to +85 C for industrial, -40 C to +125 C extended, unless otherwise specified. Symbol VREF TC(VREF) Parameter band gap reference voltage band gap temperature coefficient Conditions Min 1.11 Typ[1] 1.23 10 Max 1.34 20 Unit V ppm/ C
[1] [2] [3] [4] [5] [6] [7]
Typical ratings are not guaranteed. The values listed are at room temperature, 3 V. The IDD(oper), IDD(idle), and IDD(PD) specifications are measured using an external clock with the following functions disabled: comparators, brownout detect, ADC, I2C-bus, UART, SPI, and Watchdog timer. Pin capacitance is characterized but not tested. Measured with port in quasi-bidirectional mode. Measured with port in high-impedance mode. Ports in quasi-bidirectional mode with weak pull-up (applies to all port pins with pull-ups) Port pins source a transition current when used in quasi-bidirectional mode and externally driven from logic 1 to logic 0. This current is highest when VIN is approximately 2 V.
9397 750 14397
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
58 of 72
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
12. Dynamic characteristics
Table 14: AC characteristics VDD = 2.4 V to 3.6 V, unless otherwise specified. Tamb = -40 C to +85 C for industrial, -40 C to +125 C extended, unless otherwise specified.[1] Symbol fRCOSC Parameter Conditions Variable clock Min industrial internal RC oscillator frequency (nominal f = 7.3728 MHz) trimmed extended to 1 % at Tamb = 25 C internal Watchdog oscillator frequency (nominal f = 400 kHz) oscillator frequency clock cycle CLKLP active frequency high time low time rise time fall time glitch rejection, P1.5/RST pin signal acceptance, P1.5/RST pin glitch rejection, any pin except P1.5/RST signal acceptance, any pin except P1.5/RST Shift register (UART mode 0) tXLXL tQVXH tXHQX tXHDX tDVXH serial port clock cycle time output data set-up to clock rising edge output data hold after clock rising edge input data hold after clock rising edge see Figure 26 see Figure 26 see Figure 26 see Figure 26 16tCLCL 13tCLCL 150 tCLCL + 20 0 1333 1083 150 103 0 ns ns ns ns ns see Figure 27 see Figure 27 see Figure 27 see Figure 27 VDD = 2.4 V to 3.6 V see Figure 27 7.189 7.004 320 Max 7.557 7.741 520 fosc = 12 MHz Min 7.189 7.004 320 Max 7.557 7.741 520 MHz MHz kHz Unit
fWDOSC
External clock input fosc tCLCL fCLKP tCHCX tCLCX tCLCH tCHCL Glitch filter 125 50 50 15 125 50 50 15 ns ns ns ns 0 83 0 22 22 12 8 tCLCL - tCLCX tCLCL - tCHCX 8 8 22 22 8 8 MHz ns MHz ns ns ns ns
input data valid to clock rising edge see Figure 26
9397 750 14397
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
59 of 72
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
Table 14: AC characteristics...continued VDD = 2.4 V to 3.6 V, unless otherwise specified. Tamb = -40 C to +85 C for industrial, -40 C to +125 C extended, unless otherwise specified.[1] Symbol Parameter Conditions Variable clock Min SPI interface fSPI Operating frequency 2.0 MHz (Slave) 3.0 MHz (Master) tSPICYC Cycle time 2.0 MHz (Slave) 3.0 MHz (Master) tSPILEAD Enable lead time (Slave) 2.0 MHz tSPILAG Enable lag time (Slave) 2.0 MHz tSPICLKH SPICLK high time Master Slave tSPICLKL SPICLK low time Master Slave tSPIDSU tSPIDH tSPIA tSPIDIS Data set-up time (Master or Slave) see Figure 22, 23, 24, 25 Data hold time (Master or Slave) Access time (Slave) Disable time (Slave) 2.0 MHz tSPIDV Enable to output data valid 2.0 MHz 3.0 MHz tSPIOH Output data hold time see Figure 22, 23, 24, 25 see Figure 22, 23, 24, 25 0 0 0 240 167 0 240 167 ns ns ns see Figure 22, 23, 24, 25 see Figure 24, 25 see Figure 24, 25 0 240 240 ns see Figure 22, 23, 24, 25
2 3 CCLK CCLK
fosc = 12 MHz Min Max
Unit
Max
0 see Figure 22, 23, 24, 25
6 4 CCLK CCLK
CCLK 6 CCLK 4
0 -
2.0 -
MHz MHz
-
500 -
-
ns ns
see Figure 24, 25 250 see Figure 24, 25 250 see Figure 22, 23, 24, 25
2 3 CCLK CCLK
-
250
-
ns
-
250
-
ns
-
340 190
-
ns ns
120
340 190 100 100 0
120
ns ns ns ns ns
100 100 0
9397 750 14397
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
60 of 72
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
Table 14: AC characteristics...continued VDD = 2.4 V to 3.6 V, unless otherwise specified. Tamb = -40 C to +85 C for industrial, -40 C to +125 C extended, unless otherwise specified.[1] Symbol tSPIR Parameter Rise time SPI outputs (SPICLK, MOSI, MISO) SPI inputs (SPICLK, MOSI, MISO, SS) tSPIF Fall time SPI outputs (SPICLK, MOSI, MISO) SPI inputs (SPICLK, MOSI, MISO, SS)
[1]
Conditions see Figure 22, 23, 24, 25
Variable clock Min Max
fosc = 12 MHz Min Max
Unit
see Figure 22, 23, 24, 25 -
100 2000
-
100 2000
ns ns
100 2000
-
100 2000
ns ns
Parameters are valid over operating temperature range unless otherwise specified. Parts are tested to 2 MHz, but are guaranteed to operate down to 0 Hz.
9397 750 14397
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
61 of 72
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
Table 15: AC characteristics VDD = 3.0 V to 3.6 V, unless otherwise specified. Tamb = -40 C to +85 C for industrial, -40 C to +125 C extended, unless otherwise specified.[1] Symbol fRCOSC Parameter Conditions Variable clock Min industrial internal RC oscillator frequency (nominal f = 7.3728 MHz) trimmed extended to 1 % at Tamb = 25 C internal Watchdog oscillator frequency (nominal f = 400 kHz) oscillator frequency clock cycle CLKLP active frequency high time low time rise time fall time glitch rejection, P1.5/RST pin signal acceptance, P1.5/RST pin glitch rejection, any pin except P1.5/RST signal acceptance, any pin except P1.5/RST Shift register (UART mode 0) tXLXL tQVXH tXHQX tXHDX tDVXH fSPI serial port clock cycle time output data set-up to clock rising edge output data hold after clock rising edge input data hold after clock rising edge see Figure 26 see Figure 26 see Figure 26 see Figure 26 16tCLCL 13tCLCL 150 tCLCL + 20 0 888 722 150 103 0 ns ns ns ns ns see Figure 27 see Figure 27 see Figure 27 see Figure 27 see Figure 27
[1]
fosc = 18 MHz Min 7.189 7.004 320 Max 7.557 7.741 520
Unit MHz MHz kHz
Max 7.557 7.741 520
7.189 7.004 320
fWDOSC
External clock input fosc tCLCL fCLKP tCHCX tCLCX tCLCH tCHCL Glitch filter 125 50 50 15 125 50 50 15 ns ns ns ns 0 55 0 22 22 18 8 tCLCL - tCLCX tCLCL - tCHCX 5 5 22 22 5 5 MHz ns MHz ns ns ns ns
input data valid to clock rising edge see Figure 26 Operating frequency 3.0 MHz (Slave) 4.5 MHz (Master)
SPI interface 0 see Figure 22, 23, 24, 25
6 4 CCLK CCLK CCLK 6 CCLK 4
0 -
3 4.5
MHz MHz
tSPICYC
Cycle time 3.0 MHz (Slave) 4.5 MHz (Master)
-
333 222
-
ns ns
9397 750 14397
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
62 of 72
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
Table 15: AC characteristics...continued VDD = 3.0 V to 3.6 V, unless otherwise specified. Tamb = -40 C to +85 C for industrial, -40 C to +125 C extended, unless otherwise specified.[1] Symbol tSPILEAD Parameter Enable lead time (Slave) 3.0 MHz tSPILAG Enable lag time (Slave) 3.0 MHz tSPICLKH SPICLK high time Master Slave tSPICLKL SPICLK low time Master Slave tSPIDSU tSPIDH tSPIA tSPIDIS Data set-up time (Master or Slave) see Figure 22, 23, 24, 25 Data hold time (Master or Slave) Access time (Slave) Disable time (Slave) 3.0 MHz tSPIDV Enable to output data valid 3.0 MHz 4.5 MHz tSPIOH tSPIR Output data hold time Rise time SPI outputs (SPICLK, MOSI, MISO) SPI inputs (SPICLK, MOSI, MISO, SS) see Figure 22, 23, 24, 25 see Figure 22, 23, 24, 25 100 2000 100 2000 ns ns see Figure 22, 23, 24, 25 0 0 0 160 111 0 160 111 ns ns ns see Figure 22, 23, 24, 25 see Figure 24, 25 see Figure 24, 25 0 160 160 ns see Figure 22, 23, 24, 25
2 3 CCLK CCLK
Conditions see Figure 24, 25
Variable clock Min Max
fosc = 18 MHz Min Max
Unit
250 see Figure 24, 25 250 see Figure 22, 23, 24, 25
2 3 CCLK CCLK
-
250
-
ns
-
250
-
ns
-
111 167
-
ns ns
80
111 167 100 100 0
80
ns ns ns ns ns
100 100 0
9397 750 14397
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
63 of 72
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
Table 15: AC characteristics...continued VDD = 3.0 V to 3.6 V, unless otherwise specified. Tamb = -40 C to +85 C for industrial, -40 C to +125 C extended, unless otherwise specified.[1] Symbol tSPIF Parameter Fall time SPI outputs (SPICLK, MOSI, MISO) SPI inputs (SPICLK, MOSI, MISO, SS)
[1] [2]
Conditions see Figure 22, 23, 24, 25
Variable clock Min Max
fosc = 18 MHz Min Max
Unit
-
100 2000
-
100 2000
ns ns
Parameters are valid over operating temperature range unless otherwise specified. Parts are tested to 2 MHz, but are guaranteed to operate down to 0 Hz. When using an oscillator frequency above 12 MHz, the reset input function of P1.5 must be enabled. An external circuit is required to hold the device in reset at power-up until VDD has reached its specified level. When system power is removed VDD will fall below the minimum specified operating voltage. When using an oscillator frequency above 12 MHz, in some applications, an external brownout detect circuit may be required to hold the device in reset when VDD falls below the minimum specified operating voltage.
SS tCLCL tSPIF tSPICLKH SPICLK (CPOL = 0) (output) tSPICLKL tSPIR
tSPIF
tSPICLKL
tSPIR tSPICLKH
SPICLK (CPOL = 1) (output) tSPIDSU MISO (input) tSPIDH LSB/MSB in tSPIOH tSPIDV tSPIR
MSB/LSB in tSPIDV
MOSI (output)
tSPIF Master MSB/LSB out Master LSB/MSB out
002aaa156
Fig 22. SPI master timing (CPHA = 0).
9397 750 14397
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
64 of 72
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
SS tCLCL tSPIF tSPICLKL tSPIR tSPICLKH
SPICLK (CPOL = 0) (output)
tSPIF tSPICLKH
tSPICLKL
tSPIR
SPICLK (CPOL = 1) (output) tSPIDSU MISO (input) tSPIDH LSB/MSB in tSPIOH tSPIDV tSPIDV tSPIR Master MSB/LSB out Master LSB/MSB out
MSB/LSB in tSPIDV
MOSI (output)
tSPIF
002aaa157
Fig 23. SPI master timing (CPHA = 1).
SS tSPIR tSPIR tSPILAG
tSPIR tSPILEAD tSPIF
tCLCL tSPICLKH tSPICLKL
SPICLK (CPOL = 0) (input)
tSPIF
tSPICLKL
tSPIR tSPICLKH
SPICLK (CPOL = 1) (input) tSPIA MISO (output) tSPIOH tSPIDV Slave MSB/LSB out tSPIOH tSPIDV
tSPIOH tSPIDIS Slave LSB/MSB out Not defined
tSPIDSU MOSI (input)
tSPIDH
tSPIDSU
tSPIDSU
tSPIDH
MSB/LSB in
LSB/MSB in
002aaa158
Fig 24. SPI slave timing (CPHA = 0).
9397 750 14397
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
65 of 72
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
SS tSPIR tSPIR tSPILAG
tSPIR tSPILEAD tSPIF
tCLCL tSPICLKH tSPICLKL
SPICLK (CPOL = 0) (input)
tSPIF
tSPICLKL
tSPIR tSPICLKH
SPICLK (CPOL = 1) (input) tSPIOH tSPIDV tSPIA MISO (output) Not defined Slave MSB/LSB out Slave LSB/MSB out tSPIOH tSPIDV tSPIOH tSPIDV tSPIDIS
tSPIDSU MOSI (input)
tSPIDH
tSPIDSU
tSPIDSU
tSPIDH
MSB/LSB in
LSB/MSB in
002aaa159
Fig 25. SPI slave timing (CPHA = 1).
tXLXL Clock tQVXH Output Data 0 Write to SBUF Input Data Clear RI Set RI
002aaa425
tXHQX 1 tXHDX Set TI
Valid Valid Valid Valid Valid Valid Valid Valid
2
3
4
5
6
7
tXHDV
Fig 26. Shift register mode timing.
VDD - 0.5 V 0.45 V
0.2 VDD + 0.9 0.2 VDD - 0.1 V tCHCX
tCHCL
tCLCX
tC
tCLCH
002aaa416
Fig 27. External clock timing.
9397 750 14397 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
66 of 72
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
13. Comparator electrical characteristics
Table 16: Comparator electrical characteristics VDD = 2.4 V to 3.6 V, unless otherwise specified. Tamb = -40 C to +85 C for industrial, unless otherwise specified. Symbol VIO VCR CMRR Parameter offset voltage comparator inputs common mode range comparator inputs common mode rejection ratio response time comparator enable to output valid IIL
[1]
[1]
Conditions
Min 0 -
Typ 250 -
Max 20 VDD - 0.3 -50 500 10 10
Unit mV V dB ns s A
input leakage current, comparator
0 < VIN < VDD
-
This parameter is characterized, but not tested in production.
9397 750 14397
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
67 of 72
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
14. Package outline
TSSOP14: plastic thin shrink small outline package; 14 leads; body width 4.4 mm SOT402-1
D
E
A
X
c y HE vMA
Z
14
8
Q A2 pin 1 index A1 Lp L (A 3) A
1
e bp
7
wM detail X
0
2.5 scale
5 mm
DIMENSIONS (mm are the original dimensions) UNIT mm A max. 1.1 A1 0.15 0.05 A2 0.95 0.80 A3 0.25 bp 0.30 0.19 c 0.2 0.1 D (1) 5.1 4.9 E (2) 4.5 4.3 e 0.65 HE 6.6 6.2 L 1 Lp 0.75 0.50 Q 0.4 0.3 v 0.2 w 0.13 y 0.1 Z (1) 0.72 0.38 8 o 0
o
Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic interlead protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT402-1 REFERENCES IEC JEDEC MO-153 JEITA EUROPEAN PROJECTION ISSUE DATE 99-12-27 03-02-18
Fig 28. SOT402-1 (TSSOP14).
9397 750 14397
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
68 of 72
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
TSSOP16: plastic thin shrink small outline package; 16 leads; body width 4.4 mm
SOT403-1
D
E
A
X
c y HE vMA
Z
16
9
Q A2 pin 1 index A1 Lp L (A 3) A
1
e bp
8
wM detail X
0
2.5 scale
5 mm
DIMENSIONS (mm are the original dimensions) UNIT mm Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic interlead protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT403-1 REFERENCES IEC JEDEC MO-153 JEITA EUROPEAN PROJECTION ISSUE DATE 99-12-27 03-02-18 A max. 1.1 A1 0.15 0.05 A2 0.95 0.80 A3 0.25 bp 0.30 0.19 c 0.2 0.1 D (1) 5.1 4.9 E (2) 4.5 4.3 e 0.65 HE 6.6 6.2 L 1 Lp 0.75 0.50 Q 0.4 0.3 v 0.2 w 0.13 y 0.1 Z (1) 0.40 0.06 8 o 0
o
Fig 29. SOT403-1 (TSSOP16).
9397 750 14397
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
69 of 72
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
15. Revision history
Table 17: Rev Date 04 20041217 Revision history CPCN Description Product data (9397 750 14397) Modifications:
* *
03 02 01 20040701 20040512 20040408 -
Added extended temperature device (P89LPC915HDH). Added 18 MHz information.
Preliminary data (9397 750 13522) Preliminary data (9397 750 13278) Preliminary data (9397 750 12986)
9397 750 14397
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
70 of 72
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
16. Data sheet status
Level I II Data sheet status[1] Objective data Preliminary data Product status[2][3] Development Qualification Definition This data sheet contains data from the objective specification for product development. Philips Semiconductors reserves the right to change the specification in any manner without notice. This data sheet contains data from the preliminary specification. Supplementary data will be published at a later date. Philips Semiconductors reserves the right to change the specification without notice, in order to improve the design and supply the best possible product. This data sheet contains data from the product specification. Philips Semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. Relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN).
III
Product data
Production
[1] [2] [3]
Please consult the most recently issued data sheet before initiating or completing a design. The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at URL http://www.semiconductors.philips.com. For data sheets describing multiple type numbers, the highest-level product status determines the data sheet status.
17. Definitions
Short-form specification -- The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition -- Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 60134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information -- Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification.
customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes -- Philips Semiconductors reserves the right to make changes in the products - including circuits, standard cells, and/or software - described or contained herein in order to improve design and/or performance. When the product is in full production (status `Production'), relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no licence or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified.
19. Licenses
Purchase of Philips I2C components Purchase of Philips I2C components conveys a license under the Philips' I2C patent to use the components in the I2C system provided the system conforms to the I2C specification defined by Philips. This specification can be ordered using the code 9398 393 40011.
18. Disclaimers
Life support -- These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors
Contact information
For additional information, please visit http://www.semiconductors.philips.com. For sales office addresses, send e-mail to: sales.addresses@www.semiconductors.philips.com.
9397 750 14397
Fax: +31 40 27 24825
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 04 -- 17 December 2004
71 of 72
Philips Semiconductors
P89LPC915/916/917
8-bit microcontrollers with accelerated two-clock 80C51 core
Contents
1 2 3 4 4.1 5 6 6.1 6.2 7 7.1 8 9 9.1 9.2 9.2.1 9.2.2 9.2.3 9.3 9.4 9.5 9.6 9.7 9.8 9.9 9.9.1 9.9.2 9.9.3 9.9.4 9.9.5 9.9.6 9.9.7 9.9.8 9.10 9.11 9.11.1 9.12 9.12.1 9.12.2 9.12.3 9.12.4 9.12.5 9.12.6 9.12.7 9.13 9.13.1 9.13.2 9.14 9.14.1 9.14.2 9.14.3 9.15 9.16 General description . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Additional features . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Ordering options . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Pinning information. . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Logic symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Product comparison . . . . . . . . . . . . . . . . . . . . . . . . . 16 Special function registers. . . . . . . . . . . . . . . . . . . . . 16 Functional description . . . . . . . . . . . . . . . . . . . . . . . 29 Enhanced CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Clocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Clock definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 CPU clock (OSCCLK) . . . . . . . . . . . . . . . . . . . . . . . 29 Clock output (P89LPC917) . . . . . . . . . . . . . . . . . . . 29 On-chip RC oscillator option . . . . . . . . . . . . . . . . . . 29 Watchdog oscillator option . . . . . . . . . . . . . . . . . . . . 30 External clock input option . . . . . . . . . . . . . . . . . . . . 30 CPU Clock (CCLK) wake-up delay. . . . . . . . . . . . . . 30 CPU Clock (CCLK) modification: DIVM register . . . 30 Low power select . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 A/D converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 General description . . . . . . . . . . . . . . . . . . . . . . . . . 32 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 A/D operating modes . . . . . . . . . . . . . . . . . . . . . . . . 33 Conversion start modes . . . . . . . . . . . . . . . . . . . . . . 34 Boundary limits interrupt . . . . . . . . . . . . . . . . . . . . . 35 DAC output to a port pin with high output impedance 35 Clock divider. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Power-down and Idle mode . . . . . . . . . . . . . . . . . . . 35 Memory organization . . . . . . . . . . . . . . . . . . . . . . . . 35 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 External interrupt inputs . . . . . . . . . . . . . . . . . . . . . . 36 I/O ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Port configurations . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Quasi-bidirectional output configuration. . . . . . . . . . 38 Open-drain output configuration. . . . . . . . . . . . . . . . 39 Input-only configuration . . . . . . . . . . . . . . . . . . . . . . 39 Push-pull output configuration . . . . . . . . . . . . . . . . . 39 Port 0 analog functions . . . . . . . . . . . . . . . . . . . . . . 39 Additional port features . . . . . . . . . . . . . . . . . . . . . . 40 Power monitoring functions . . . . . . . . . . . . . . . . . . . 40 Brownout detection . . . . . . . . . . . . . . . . . . . . . . . . . 40 Power-on detection . . . . . . . . . . . . . . . . . . . . . . . . . 40 Power reduction modes . . . . . . . . . . . . . . . . . . . . . . 40 Idle mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Power-down mode . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Total Power-down mode . . . . . . . . . . . . . . . . . . . . . . 41 Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Timers/counters 0 and 1 . . . . . . . . . . . . . . . . . . . . . 42 Mode 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Mode 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Mode 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Mode 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Mode 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Timer overflow toggle output. . . . . . . . . . . . . . . . . . . 43 Real-Time clock/system timer. . . . . . . . . . . . . . . . . . 43 UART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Mode 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Mode 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Mode 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Mode 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Baud rate generator and selection . . . . . . . . . . . . . . 44 Framing error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Break detect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Double buffering . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Transmit interrupts with double buffering enabled (Modes 1, 2 and 3) . . . . . . . . . . . . . . . . . . . 45 9.18.10 The 9th bit (bit 8) in double buffering (Modes 1, 2 and 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 9.19 I2C-bus serial interface . . . . . . . . . . . . . . . . . . . . . . . 46 9.20 Serial Peripheral Interface (SPI - P89LPC916). . . . . 47 9.20.1 Typical SPI configurations. . . . . . . . . . . . . . . . . . . . . 49 9.21 Analog comparators . . . . . . . . . . . . . . . . . . . . . . . . . 51 9.22 Internal reference voltage . . . . . . . . . . . . . . . . . . . . . 51 9.23 Comparator interrupt. . . . . . . . . . . . . . . . . . . . . . . . . 51 9.24 Comparator and power reduction modes . . . . . . . . . 52 9.25 Keypad interrupt (KBI) . . . . . . . . . . . . . . . . . . . . . . . 52 9.26 Watchdog timer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 9.27 Additional features . . . . . . . . . . . . . . . . . . . . . . . . . . 53 9.27.1 Software reset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 9.27.2 Dual data pointers. . . . . . . . . . . . . . . . . . . . . . . . . . . 53 9.28 Flash program memory. . . . . . . . . . . . . . . . . . . . . . . 53 9.28.1 General description. . . . . . . . . . . . . . . . . . . . . . . . . . 53 9.28.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 9.28.3 Flash organization . . . . . . . . . . . . . . . . . . . . . . . . . . 54 9.28.4 Flash programming and erasing . . . . . . . . . . . . . . . . 54 9.28.5 In-circuit programming (ICP). . . . . . . . . . . . . . . . . . . 54 9.28.6 In-application programming (IAP-Lite) . . . . . . . . . . . 55 9.28.7 Using flash as data storage . . . . . . . . . . . . . . . . . . . 55 9.28.8 User configuration bytes . . . . . . . . . . . . . . . . . . . . . . 55 9.28.9 User sector security bytes . . . . . . . . . . . . . . . . . . . . 55 10 Limiting values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 11 Static characteristics . . . . . . . . . . . . . . . . . . . . . . . . . 57 12 Dynamic characteristics . . . . . . . . . . . . . . . . . . . . . . 59 13 Comparator electrical characteristics . . . . . . . . . . . 67 14 Package outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 15 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 16 Data sheet status . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 17 Definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 18 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 19 Licenses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 9.16.1 9.16.2 9.16.3 9.16.4 9.16.5 9.16.6 9.17 9.18 9.18.1 9.18.2 9.18.3 9.18.4 9.18.5 9.18.6 9.18.7 9.18.8 9.18.9
(c) Koninklijke Philips Electronics N.V. 2004. Printed in the U.S.A.
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights. Date of release: 17 December 2004 Document order number: 9397 750 14397

▲Up To Search▲

Price & Availability of P89LPC915HDH

	To Download P89LPC915HDH Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .